Cisco Catalyst 2960-X Command Reference

spanning-tree bpdufilter
To enable bridge protocol data unit (BPDU) filtering on the interface, use the spanning-tree bpdufilter
command in interface configuration mode. To return to the default settings, use the no form of this command.
spanning-tree bpdufilter {enable| disable}
no spanning-tree bpdufilter
Syntax Description
Enables BPDU filtering on this interface.enable
Disables BPDU filtering on this interface.disable
Command Default
The setting that is already configured when you enter the spanning-tree portfast bpdufilter default command.
Command Modes
Interface configuration
Command History
ModificationRelease
This command was introduced.Cisco IOS 15.0(2)EX
Usage Guidelines
This command has three states:
• spanning-tree bpdufilter enable —Unconditionally enables BPDU filtering on the interface.
• spanning-tree bpdufilter disable —Unconditionally disables BPDU filtering on the interface.
• no spanning-tree bpdufilter —Enables BPDU filtering on the interface if the interface is in the
operational PortFast state and if you configure the spanning-tree portfast bpdufilter default command.
Be careful when you enter the spanning-tree bpdufilter enable command. Enabling BPDU filtering on
an interface is similar to disabling the spanning tree for this interface. If you do not use this command
correctly, you might create bridging loops.
Caution
You can enable BPDU filtering when the switch is operating in the per-VLAN spanning-tree plus (PVST+)
mode, the rapid-PVST mode, or the multiple spanning-tree (MST) mode.
You can globally enable BPDU filtering on all Port Fast-enabled interfaces with the spanning-tree portfast
bpdufilter default command.
The spanning-tree bpdufilter enable command overrides the PortFast configuration.
Catalyst 2960-X Switch Layer 2 Command Reference, Cisco IOS Release 15.0(2)EX
78 OL-29043 -01
Layer 2 Commands
spanning-tree bpdufilter

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g