Cisco Catalyst 2960-X Command Reference

INDEX
C
channel-group command 20
channel-protocol command 23
clear lacp command 25
clear pagp command 26
clear spanning-tree counters command 27
clear spanning-tree detected-protocols command 28
D
debug etherchannel command 29
debug lacp command 31
debug pagp command 32
debug platform etherchannel command 34
debug platform pm command 35
debug platform udld command 40
debug spanning-tree command 38
I
interface port-channel command 41
L
lacp port-priority command 43
lacp system-priority command 45
link state group command 47
link state track command 48
P
pagp learn-method command 49
pagp port-priority command 51
pagp timer command 53
port-channel load-balance command 54
S
show etherchannel command 55
show lacp command 58
show link state group command 63
show pagp command 64
show platform backup interface command 66
show platform etherchannel command 67
show platform pm command 68
show platform spanning-tree command 70
show spanning-tree command 71
show udld command 74
spanning-tree backbonefast command 77
spanning-tree bpdufilter command 78
spanning-tree bpduguard command 80
spanning-tree cost command 81
spanning-tree etherchannel guard misconfig command 83
spanning-tree extend system-id command 84
spanning-tree guard command 86
spanning-tree link-type command 88
spanning-tree loopguard default command 89
spanning-tree mode command 90
spanning-tree mst configuration command 92
spanning-tree mst cost command 94
spanning-tree mst forward-time 95
spanning-tree mst hello-time command 96
spanning-tree mst max-age command 97
spanning-tree mst max-hops command 98
spanning-tree mst port-priority command 99
spanning-tree mst pre-standard command 100
spanning-tree mst priority command 101
spanning-tree mst root command 102
spanning-tree pathcost method command 104
spanning-tree port-priority command 105
spanning-tree portfast command (global configuration) 106
spanning-tree portfast command (interface configuration) 108
spanning-tree transmit hold-count command 110
spanning-tree uplinkfast command 111
spanning-tree vlan command 113
switchport access vlan command 115
switchport mode command 116
switchport nonegotiate command 119
Catalyst 2960-X Switch Layer 2 Command Reference, Cisco IOS Release 15.0(2)EX
OL-29043 -01 IN-1

Cisco Catalyst 2960-X Specifications

General

Console port	RJ-45
USB 2.0 ports quantity	2
SFP module slots quantity	4
Installed SFP modules quantity	-
Gigabit Ethernet (copper) ports quantity	48
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Power source	AC
Input current	5 A
AC input voltage	100 - 240 V
Power consumption (typical)	60.9 W
Number of power supply units	1
Redundant power supply (RPS) support	Yes
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 4000 m
Storage temperature (T-T)	-25 - 70 °C
Operating temperature (T-T)	-5 - 40 °C
Operating relative humidity (H-H)	10 - 95 %
Switching protocols	UDP, TCP, RADIUS/TACACS+
Number of VLANs	1023
Networking standards	IEEE 802.1ab, IEEE 802.1D, IEEE 802.1p, IEEE 802.1Q, IEEE 802.1s, IEEE 802.1w, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3ad, IEEE 802.3ae, IEEE 802.3af, IEEE 802.3ah, IEEE 802.3at, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Throughput	107.1 Mpps
Jumbo frames	9216
Number of queues	8
MAC address table	16000 entries
Number of static routes	1000
DHCP features	DHCP server
Authentication	MAC-based authentication, Port-based authentication
Security algorithms	802.1x RADIUS, SNMP, SSH
Access Control List (ACL) rules	3
Switch type	Managed
Switch layer	L2/L3
Safety	UL 60950-1, CAN/CSA-C22.2 No. 60950-1, EN 60950-1, IEC 60950-1, AS/NZS 60950-1
Form factor	1U
Product color	Black
Total Power over Ethernet (PoE) budget	370 W
Power over Ethernet (PoE) ports quantity	24
Power over Ethernet plus (PoE+) ports quantity	12
Memory type	DRAM
Noise level	39 dB
Flash memory	128 MB
Internal memory	512 MB
Processor frequency	600 MHz
Mean time between failures (MTBF)	276870 h

Weight and Dimensions

Depth	368 mm
Width	445 mm
Height	45 mm
Weight	5800 g