Clarion CZ215E User Manual

Audio Setup
12
CZ215E/CZ315E
English
S-RESTORER V-BASS D-BEAT
•฀ S-RESTORER (Sound Restorer):
full quality sound reproduction of
compressed audio data (default: MID)
•฀ V-BASS (Virtual Bass): delivers
powerful lows just like an add-on
subwoofer (default: OFF)
•฀ D-BEAT (Dynamic Beat Enhancer):
(default: HIGH)
1. Press [ROTARY] knob.
2. Turn [ROTARY ] knob to adjust the
value.
S-RESTORER/V-BASS/D-BEAT: OFF/
LOW/MID/HIGH.
setting: –6 ~ +6
4. Long press [1]~[3] button to store the
setting into “USER 1” ~“USER 3”
memory.
Note:
•฀If฀you฀do฀not฀perform฀storing฀as฀step฀4฀
when฀you฀select฀“BASS BOOST/HIGH
BOOST/VOCAL/IMPACT/NATUAL”฀,฀
the฀setting฀will฀be฀stored฀in฀“CUSTOM฀”฀
temporarily.
Setting Intelligent Tune
1. Select “INTEL- TUNE” in audio items,
and press [ROTARY ] knob.
2. Press [
x
] or [
v
] button, the tone
effect changes.
System Setup
1. Long press [
] button.
2. Then press [
x
] or [
v
] button to
select the system setup items:
TA AF REG PTY AUTO
STORE
DX/LO AUX SENS
BT SELECT BT DELETE
BT DISCON A-ANSWER
A-CONNECT
TEL MEMORY PIN
CODE
DIMMER BEEP EQ-
SELECT
LANGUAGE
※
RESET
•฀ BT SELECT: select paired device
•฀ BT DELETE: delete paired device
•฀ BT DISCON: disconnect device
•฀ A-ANSWER: auto answer
•฀ A-CONNECT: auto connect
•฀ TEL MEMORY: priority for phonebook
download
•฀ DIMMER: dimmer control
•฀ BEEP: button beep sound
•฀ EQ-SELECT: select rear or subwoofer
•฀ LANGUAGE: title display language
setting
•฀ RESET: memory reset
∗
These items are setting for the different
source mode. The detailed operations
please follow the following source mode
operations chapter.
※You should press [ROTA RY ] knob to adjust
the setting for this item.
3. Turn [ROTARY ] knob to adjust the
setting.
•฀ BT SELECT/BT DELETE/BT DISCON/
A-ANSWER/A-CONNECT:
detailed operations are below
•฀ DIMMER: ON/OFF (default: ON)
•฀ BEEP: TYPE-A/TYPE-B/OFF (default:
TYPE-A)
•฀ EQ-SELECT: G-EQ, BASS/TREBLE
(default: G-EQ)
•฀ LANGUAGE: ENG(English)/
PYC(Russian) (default: ENG)
•฀ RESET: detailed operations are below
4. After completing settings, press [DISP]
button to return to the previous mode.
Note:
•฀You฀can฀press฀[DISP]฀button฀to฀return฀to฀
the฀previous฀layer฀duiring฀operations.
Select Paired Device
This is a setting for user to select one of
the paired mobile phones to connect.
1. Select “BT SELECT” in system setup
items.
2. Turn the [ROTARY] knob to choose one
of the paired devices.
3. Press the [ROTARY] knob to connect.
Delete Paired Device
This is a setting for user to delete one of
the paired device from the list.
1. Select “BT DELETE” in system setup
items.
2. The paired device appears in the
*
CZ315E
only
CZ315E&CZ215E Owner's Guide A6 1112.indd 122015/01/09 9:25:38

Clarion CZ215E Specifications

General

Brand	Clarion
Model	CZ215E
Category	Car Receiver
Language	English