Clarion VRX8271 - Equalizer Adjustments

Note:
• If the control is idle for about 5 seconds after each
operation, the unit returns to the previous mode.
1) Press the EQ button 04) to go to the equaliz¬
er mode.
2) Press the BAND button [8j to select EQ
BASIC or EQ USER.
Each time you press the BAND button [a],
the EQ BASIC and EQ USER toggles.
EQ BASIC: This menu consists of the 6
equalizer characteristics initially set.
EQ USER: The menu containing user-set
equalizer characteristics (for setting the
characteristics, see the next subsection
“Setting and storing the equalizer charac¬
teristics.” The equalizer No. where no set¬
ting is made becomes flat.)
3) Press No. 1 to 6 of the preset buttons [U to
select the equalizer characteristic to be set.
Button
No.
EQ BASIC EQ USER
No.1 BAS Bass is
(BASS BOOST) emphasized.
US1
No.2
HIG Treble is
(HIGH BOOST) emphasized.
US2
No.3
ACO Mean (human
(ACOUSTICAL) voice) is
emphasized.
US3
No.4
IMP(IMPACT) Bass and
treble are
emphasized.
US4
No.5
SMO Sound level of
(SMOOTH) each band is
smoothed.
US5
No.6
FLA(FLAT) Original sound
(flat equalizing)
US6
Note:
• Turn on the equalizer effect after following the
instructions in the next subsection ‘Turning on
and off the equalizer effect." Otherwise, the above
settings will be invalidated.
Turning on and off the equalizer effect
1) Press the ADJ button 02 to go to the CON¬
FIGURATION mode.
2) Slide the Up/Down button Lit to ▼ (down) or
A (up) to move the cursor to “EQ”.
3) Slide the Up/Down button [Tj to ► (right) to
turn “OFF" and “ON”.
4) Press the ADJ button 01 to return to the pre¬
vious mode.
Setting and storing the equalizer
characteristics
You can set your own equalizer characteristics
and store them to “EQ USER” (US1 to US6). Up
to 6 patterns can be stored.
Notes:
• This setting cannot be edited when EQ in the
CONFIGURATION display is turned off.
• If the control is idle for about 5 seconds after each
operation, the unit returns to the previous mode.
1) Press the EQ button 02 to go to the equaliz¬
er mode.
2) Press the BAND button [Fj to select “EQ
USER."
3) Press (center) of the Up/Down button
CD when the “EQ USER" is displayed.
4) Slide the Up/Down button CD to ^ (left) or
► (right) to select the frequency and slide to
▲ (up) or T (down) to adjust the sound
level.
* Repeat the above procedures to set the char¬
acteristics.
* The frequency selection option differs accord¬
ing to the connection unit as follows:
DSP/EQ
type
Frequency to be
selected
Sound level to
be adjusted
DPH9100
DPH7100
30/50 Hz, 100 Hz,
200 Hz, 400 Hz,
1 kHz, 3 kHz, 12 kHz
-12 dB to
+12 dB
EQH5100
30 Hz. 60 Hz, 120 Hz,
200 Hz
-15 dB to
+15 dB
400 Hz, 1 kHz, 3 kHz,
8 kHz, 12 kHz
-12 dB to
+12 dB
5) After setting the characteristics, press and
hold one of the Preset buttons [9j (No. 1 to
No. 6) where you want to store the setting.
A beep sounds when the setting is stored.
6) Press the EQ button 02 to return to the pre¬
vious mode.
29