CLIVET ELFOFresh2 CPAN-U 70-120 Series - Page 70

70 ELFOFresh² BT15B012GB-00
Sizes 200-650
Unit for the renewal and purication of air with thermodynamic active recovery for indoor installation. Complete with high-eciency refrigeration circuit,
that can be reversed into a heat pump with rotary airtight compressor with R134A refrigerant, low-consumption supply and extraction fans with electronic
control, built-in, cabled controls with re-positionable electrical panel complete with electronic control and all protection and safety devices.
Structure made entirely from “aluzink” plate that guarantees excellent mechanical characteristics and high corrosion strength over time. The ventilating
section is completely lined with anti-condensate and soundproong material.
Refrigeration circuit with airtight rotary compressor mounted on anti-vibration rubber grommets and complete with oil charge and suction lter, refrigerant
charge, high pressure safety pressure switch, suction pressure transducer, 4-way cycle inversion valve, lamination capillary and liquid receiver.
Direct expansion, nned coil exchangers for pretreatment of outdoor air and energy recovery from exhaust air, made from copper tubes arranged in
staggered rows and mechanically expanded for improved adherence to the collar of the ns.
The ns are made from aluminium with a special corrugated surface, set a suitable distance apart to ensure maximum heat exchange eciency.
Condense collection tray made of 1050 H24 aluminium alloy with anti-condensation insulation, welded and equipped with siphon drain tube.
Centrifugal supply and exhaust fans with high energy eciency and double intake, brushless electric motor directly coupled to the fan with plastic auger
and impeller with diameter of 146 mm, maximum available pressure of 120 Pa that can be calibrated for operation based on the eective pressure drops
in the system.
Pleated lter, made up of a galvanized plate frame with galvanized and electric-welded protective mesh and 100% regenerable polyester ltering media
with PVC resin. G3 eciency according to CEN-EN 779 standard (Eurovent class EU3 - average eciency 84% ASHRAE 52 - 76 Atm). Self-extinguishing
(resistance to re class 1 - DIN 53438). Metal mesh pre-lter with G1 eciency.
The electrical panel assembled outside the unit is connected to it by a fast- connect cable (2 mt) that allows its remotization in positions where the
maintenance/control of the parameters is easier. The power section includes: - fuses compressor and fans, fans control contactors and compressor control
contactor.
The control section consists of a Board with microprocessor control system that manages the control of the unit based on the outdoor and indoor air
conditions and includes: outdoor air temperature probe, temperature and humidity probe for room supply air, return ambient air temperature probe and
potential-free contacts for remote ON/OFF, summer/winter mode, silent mode and ventilation only.
Thermodynamic recovery function active in summer and winter; Dehumidify is perfect in summer for matching with the radiant cooling FREECOOLING.
HID-P1 room thermostat with ambient temperature and humidity probe connected to the unit via a shielded twisted pair at a maximum distance of 15 m
with the following functions: setting the desired room temperature and humidity, ON/OFF, summer/winter mode setting, fan-only mode setting, diagnostic
management with code specic to the type of error.
Based on the unit’s conguration:
Setup to ELFOSystem with RS485 Modbus PRELF
Plug-in electronic board for connection to ELFOSystem using Modbus RS485 serial port
Electronic lter FES
High-eciency electrostatic lter for the ltration of the renewal air to eliminate fumes, particulates, bacteria and viruses.
Heating elements in duct EHPCX
Modulating electric heaters kit in the duct for preheating the renewal air coming from the outside with temperatures below -5°C.
Immersed electrode humidier HSE3LX/HSE3MX
Immersed electrode humidier for humidication of renewal air in heating operation, equipped with power supply and independent loading and draining.
ELFOFresh² 200 TECHNICAL DATA
-
R410A refrigerant
-
Heating capacity under nominal conditions (A7/A20) 1,81 kW, eciency factor COP=4,1
-
Cooling capacity under nominal conditions (A35/A27) 1,63 kW,eciency factor EER=2,87
-
Nominal air ow 200 m³/h, Voltage 230/1/50
-
CPAN-U 200 Clivet model
ELFOFresh² 300 TECHNICAL DATA
-
R410A refrigerant
-
Heating capacity under nominal conditions (A7/A20) 2,33 kW, eciency factor COP=3,93
-
Cooling capacity under nominal conditions (A35/A27) 2,17 kW,eciency factor EER=2,96
-
Nominal air ow 300 m³/h, Voltage 230/1/50
-
CPAN-U 300 Clivet model
ELFOFresh² 500 TECHNICAL DATA
-
R410A refrigerant
-
Heating capacity under nominal conditions (A7/A20) 3,58 kW, eciency factor COP=4,27
-
Cooling capacity under nominal conditions (A35/A27) 3,13 kW,eciency factor EER=2,86
-
Nominal air ow 500 m³/h, Voltage 230/1/50
-
CPAN-U 500 Clivet model
ELFOFresh² 650 TECHNICAL DATA
-
R410A refrigerant
-
Heating capacity under nominal conditions (A7/A20) 5 kW, eciency factor COP=3,94
-
Cooling capacity under nominal conditions (A35/A27) 4,23 kW,eciency factor EER=2,78
-
Nominal air ow 650 m³/h, Voltage 230/1/50
-
CPAN-U 650 Clivet model
COP and EER are calculated according to the standard EN14511:2008