COMEM eSDB10 - Page 18

18
Figura 11
Posizionare la guarnizione piana tra le due ange.
ATTENZIONE
eSDB-15/30
Primo passaggio: Rimuovere nastro/tappo di plastica dai
punti di ingresso/uscita dell'aria. Fissare la angia superi-
ore (Fig.10/A) nella angia della tubazione del conserva-
tore (Fig.10/B) utilizzando N°4 viti M12 (Fig.10/C).
Secondo passaggio: Vericare che la bolla (Fig.16/17/18)
si trovi all'interno del cerchio nero.
Terzo passaggio: svitare la vite presente nella parte
inferiore dell'essiccatore (Fig.11/A) no a ne corsa utile
della vite.
Figura 12
Figura 10
Il produttore del trasformatore può scegliere se installare il
supporto antivibrante che è fornito con l'essiccatore eSDB sulla
base della robustezza della supporto superiore (fig.12/A).
NOTA
Tra il connettore ed il foro sulla flangia posizionare una
guarnizione OR al fine di garantire la tenuta.
Tubo e connettori devono essere assemblati al fine di garantire
la tenuta.
AVVERTIMENTO
D
C
B
A
654
3
21 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEETITERREVSTATUSDOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLECOMPANY
Component Drawing-
PROJECT IDWORK ORDER IDBASED ON DOC IDDOCUMENT KINDAPPROVED ON
- -Diego Boro
APPROVED BYREVIEWED BYCREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A
D
C
B
A
654
3
21 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEETITERREVSTATUSDOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLECOMPANY
Component Drawing-
PROJECT IDWORK ORDER IDBASED ON DOC IDDOCUMENT KINDAPPROVED ON
- -Diego Boro
APPROVED BYREVIEWED BYCREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
B
A
C
D
C
B
A
654
3
21 7 8
E
F
A
B
C
D
E
F
1 2 3 4 5 6 7 8
This document is issued by means of a computerized system. The digitally stored original is electronically approved. The approved document has a date entered in the `Approved'-field. A manual signature is not required.
DRAWING SHEET ISO 5457: 1999-A3T
We reserve all rights in this document and in the information contained therein. Reproduction, use or disclosure to third parties without express authority is strictly fobidden.
1/1 2
A
Development
NE-1188
SHEETITERREVSTATUSDOCUMENT ID
ITABB-9AAE306693
-
RESPONSIBLE DEPARTMENT
COMEM ESDB10
COMEM
TITLE / SUPPLEMENTARY TITLECOMPANY
Component Drawing-
PROJECT IDWORK ORDER IDBASED ON DOC IDDOCUMENT KINDAPPROVED ON
- -Diego Boro
APPROVED BYREVIEWED BYCREATED BY
© COPYRIGHT ALL RIGHTS RESERVED
A
ESSICCATORI AUTORIGENERANTI eSDB 10/15/30