ConMed 7550 - Service Manual

54 pages

Save Page as PDF

To Next Page

Service Manual

Main Page

Table of Contents3
Circuit Descriptions7
Introduction7
Display Panel Assembly [A5]7
General Information7
Mailbox [U19]7
Power Adjustments [U16 & U33]7
Activation Requests [U16 & U33]8
Mode Select Encoders [U31 & U32]8
Display Drivers - Seven Segment [U14, U20, U39, U40, U41, & U17]9
Indicator Driver [U34]9
Firmware [U28 & U1]9
Ram [U2 -6116]9
A/D Inputs [Control Microcontroller]9
A/D Inputs [Monitor Microcontroller]10
EEPROM & Driver [U37, U27]10
D/A Converter [U12]10
Keyboard Scanner [U5]11
Monitoring [U29]11
Output PIA [U21]11
T_Mon [U35]11
Power Control Assembly [A4]11
Power Control - Full Bridge Amplifier12
RF Logic [U7 on the Power Control Assembly]13
Power Control - I/O Signals14
ABC™ Arc Sense14
High Voltage Power Supply [A7]15
Power Supply Topology15
Phase Control Output15
HVPS Isolation Components16
HVPS Low Voltage Components17
Hv/Flow Control Assembly [A1]17
Line Synchronization Circuit17
HV Regulation Control Loop18
Argon Flow Control [A1]19
Pneumatic Circuit19
Mass Flow Rate Regulation20
Smart Sense21
Full Bridge Amplifier [A8]21
Single-Ended Amplifier [A9]22
RF Output Assembly/Components [A10]23
Low Voltage Power Supply [A6]24
HS/A.R.M. Assembly [A11]24
6.11.1 Handsense Circuit24
Aspen Return Monitor (A.R.M.)25
6.11.3 RF Leakage Monitor26
6.11.4 Transformer Select Relays26
6.11.5 Arc Sense Transformer26
Maintenance/Checkout27
Introduction27
Cleaning27
Generator & Mobile Storage Assembly27
Access to Circuits & Factory Settings28
Default Settings (Factory Settings)28
AC Mains Frequency & Voltage28
Initial Setup & Test29
Accessory Connections29
Display Panel Testing29
Activation Testing31
RF Output Power Checks31
Argon Flow Testing32
Remote Power Control Testing32
Return Monitor (A.R.M. - Aspen Return Monitor)33
Pulsed Cut Mode34
RF Leakage Test34
Final Checks34
Mobile Storage Pedestal (Cart)34
Calibration37
Introduction37
Equipment List37
Standard Equipment List37
Optional Calibration Equipment List37
Test Leads & Adaptors37
Calibration Set-Up37
Calibration (HS/A.R.M. Assembly - A11)37
10 Ohm A.R.M. Calibration37
150 Ohm A.R.M. Calibration38
High Voltage Calibration (Hv/Flow Control Assembly - A1)38
HV RAMP Calibration38
High Voltage Adjust38
HV_MON Adjust38
Dp Calibration (Differential Pressure)38
PABS Calibration (Absolute Pressure)38
Flow Rate Calibration (Optional)38
FMON Calibration39
Power Calibration39
Filter Calibration - Full Bridge Modes (Optional)39
Cut Power Calibration (Power Control Assembly - A4)39
Pinpoint Coag Calibration (Power Control Assembly - A4)39
Spray Coag Calibration (Power Control Assembly - A4)39
Bipolar Calibration (Power Control Assembly - A4)40
ABC Calibration (Power Control Assembly - A4)40
ABC over Voltage Calibration (Power Control Assembly - A4) [Optional]40
EEPROM Calibration40
Spray Coag PW_MEA Loading40
ABC PW_MEA Loading40
A.R.M. Max Voltage Loading40
IEC RF Leakage Measurement [Optional]41
Introduction45
Control Microcontroller Failure Codes and Troubleshooting Tips46
Monitoring Microcontroller Failure Codes and Troubleshooting Tips47
Additional Troubleshooting Tips (Non-Error Code Related49
Error Storage and Retrieval51
Error Display Configuration51
Example Error52

Need help?

Do you have a question about the ConMed 7550 and is the answer not in the manual?

ConMed 7550 Specifications

General

Brand	ConMed
Model	7550
Category	Portable Generator
Language	English

Related product manuals

ConMed System 2450

36 pages

ConMed 7550 - Service Manual

Table of Contents

ConMed 7550 Specifications

Related product manuals