Craftsman CMPPN23 User Manual

3
ENGLISH
is used, the tool can remain charged with air
after disconnecting and thus will be able to drive
a fastener even after the air line is disconnected
possibly causinginjury.
• Do not pull the trigger while connected to the air
supply as the tool may cycle, possibly causinginjury.
• Always disconnect air supply: 1.) Before making
adjustments; 2.) When servicing the tool; 3.) When
clearing a jam; 4.) When tool is not in use; 5.) When
moving to a different work area, as accidental
actuation may occur, possibly causinginjury.

WARNING: When loading tool:
• Never place a hand or any part of body in fastener
discharge area oftool.
• Never point tool at yourself or anyoneelse.
• Do not pull the triggers as accidental actuation
may occur, possibly causinginjury.
• Be careful when handling fasteners, especially
when loading and unloading, as the fasteners have
sharppoints.

WARNING: Do not operate tool if:
• There is any damage to air hose or fitting.
• The tool leaks air.
• The tool has received a sharp blow, malfunctions
or is dropped or damaged in any manner. Return
tool to the nearest authorized service facility for
examination, repair, or mechanicaladjustment.
• Warning labels are missing ordamaged.
• Tool is not in proper working order. Tags and
physical segregation shall be used forcontrol.
• Tool is without workpiece contact. A tool without
workpiece contact can be fired unintentionally
causing injury to an operator or a bystander.

WARNING: When operating the tool:
• Always handle the tool with care:
- Never engage inhorseplay.
- Never pull the trigger unless nose is directed
toward thework.
- Never point the tool at yourself orothers.
- Keep others a safe distance from the tool while
tool is in operation as accidental actuation
may occur, possibly causinginjury.
- Keep bystanders and children away while
operatingtool.
- Respect tool as a workingimplement.
- Stay alert, focus on your work and use
common sense when working withtools.
- Do not use tool while tired, after having
consumed drugs or alcohol, or while under the
influence ofmedication.
- Do not overreach. Only use in a safe
workingplace.
- Keep proper footing at alltimes.
• When working close to an edge of a workpiece
or at steep angles use care to minimize chipping,
IMPORTANT SAFETY INSTRUCTIONS

WARNING: Only persons who have read and
understand the tool operating/safety instructions
should operate thetool.

WARNING: Actuating tool may result in flying debris,
collation material, or dust which could harm operator’s
eyes. Operator and others in work area MUST wear
safety glasses with side shields. These safety glasses
must conform to ANSI Z87.1 requirements (approved
glasses have “Z87” printed or stamped on them).
Employer is responsible for enforcing the usage of eye
protection equipment by the tool operator and all other
personnel in the workarea.

WARNING: Always assume that the tool
containsfasteners.

WARNING: (Air and Supply)
• Do not use oxygen, combustible gases, or bottled
gases as a power source for this tool as tool may
explode, possibly causinginjury.
• Do not use supply sources which can potentially
exceed 200p.s.i.g. (14kg/cm
2
) as tool may burst,
possibly causinginjury.
• The connector on the tool must not hold pressure
when air supply is disconnected. If a wrong fitting
Definitions: Safety Alert Symbols andWords
This instruction manual uses the following safety alert
symbols and words to alert you to hazardous situations and
your risk of personal injury or propertydamage.

DANGER: Indicates an imminently hazardous
situation which, if not avoided, will result in death or
seriousinjury.

WARNING: Indicates a potentially hazardous situation
which, if not avoided, could result in death or
seriousinjury.

CAUTION: Indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderateinjury.

(Used without word) Indicates a safety relatedmessage.
NOTICE: Indicates a practice not related to
personal injury which, if not avoided, may result in
propertydamage.
Intended Use
Your nailer is designed for professional fasteningapplications.
DO NOT use under wet conditions or in presence of
flammable liquids orgases.
Your nailer is a professional powertool.
DO NOT let children come into contact with the tool.
Supervision is required when inexperienced operators use
thistool.
English (original instructions)

WARNING: Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
seriousinjury.
WARNING: To reduce the risk of injury, read the
instructionmanual.

Craftsman CMPPN23 Specifications

General

Brand	Craftsman
Model	CMPPN23
Category	Nail Gun
Language	English