Craftsman CMPPN23 User Manual

ENGLISH
4

WARNING: SEQUENTIAL ACTION TRIGGER
• When using the sequential action trigger, do not
actuate the tool unless the tool is placed firmly
against theworkpiece.

WARNING: DEPTH ADJUSTMENT:
• To reduce risk of serious injury from accidental
actuation when attempting to adjust depth,
ALWAYS;
• Disconnect airsupply.
• Avoid contact with trigger duringadjustments.

Do not drive nails blindly into walls, floors or other
work areas. Fasteners driven into live electrical wires,
plumbing, or other types of obstructions can result
ininjury.

Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool
while tired or under the influence of drugs or alcohol.
A moment of inattention while operating power tools
may result in serious personalinjury.

WARNING: After driving a fastener, tool may
bounce back (“recoil”) causing it to move away
from the work surface. To reduce risk of injury
always manage recoil by:
• Always maintaining control oftool.
• Allowing recoil to move tool away from
worksurface.
• Not resisting recoil such that tool will be forced
back into the work surface. In “Contact Actuation
Mode,” if workpiece contact is allowed to re‑contact
work surface before the trigger is released, an
unintended discharge of a fastener willoccur.
• Keeping face and body parts away fromtool.

WARNING: Disconnect tool:
• When not in use,
• When performing any maintenance or repairs,
• When clearing a jam,
• When elevating, lowering or otherwise moving tool
to a new location,
• When tool is outside of the operator's supervision
or control,
• When removing fasteners from themagazine.

WARNING: When maintaining the tool:
• Always shut off air supply, and disconnect tool from
air supply when not inuse.
• When working on air tools note the warnings in
this manual and use extra care when evaluating
problemtools.
Additional Safety Warnings

WARNING: Do not use this product to fasten electrical
cables. Fastening electric wires / cables could result in
electric shock or seriousharm.

WARNING: Make sure there are no electrical cables,
gas pipes, etc. that could cause a hazard if damaged by
use of thetool.
splitting or splintering, or free flight or ricochet of
fasteners, which may causeinjury.
• Do not drive fasteners on top of other fasteners
or with the tool at an overly steep angle as this
may cause deflection of fasteners which could
causeinjury.
• Do not load tool with fasteners when any one of
the operating controls isactivated.
• Use extra caution when driving fasteners into
existing walls or other blind areas to prevent
contact with hidden objects or persons on other
side (e.g., wires, pipes.)
• The operator must not pull the trigger except
during fastening operation as serious injury could
result if the tool accidentally contacts someone or
something, causing the tool tocycle.
• Keep hands and body away from the discharge
area of the tool. The tool may bounce from the
recoil of driving a fastener and an unwanted
second fastener may be driven possibly
causinginjury.
• Check operation of the trigger mechanism
frequently. Do not use the tool if the trigger is not
working correctly as accidental driving of a fastener
may result. Do not interfere with the proper
operation of the triggermechanism.
• Never inadvertently pull or grasp the trigger when
moving about, changing work location, when
holstering or hanging tool, or when preparing work
surface for fasteningoperation.
• This tool produces SPARKS during operation.
NEVER use the tool near flammable substances,
gases or vapors including lacquer, paint, benzine,
thinner, gasoline, adhesives, mastics, glues or any
other material that is ‑‑ or the vapors, fumes or
byproducts of which are ‑‑ flammable, combustible
or explosive. Using the fastenerer in any such
environment could cause an EXPLOSION resulting
in personal injury or death to user andbystanders.

WARNING: Bump Or Contact Actuation Trigger:
• When using the bump action trigger, be careful of
unintentional double fires resulting from tool recoil.
Unwanted fasteners may be driven if the contact
trip is allowed to accidentally re‑contact the work
surface.

WARNING: TO AVOID DOUBLE FIRES:
• Do not engage the tool against the work surface
with a strongforce.
• Allow the tool to recoil fully after eachactuation.
• Use sequential actiontrigger.
• When bump actuating the nailer, always keep tool
in control. Inaccurate placement of tool can result
in misdirected discharge of afastener.

Craftsman CMPPN23 Specifications

General

Brand	Craftsman
Model	CMPPN23
Category	Nail Gun
Language	English