Current Orbit Marine IC PRO LED User Manual

Safety Instructions & Warnings 1
What’s Included 2
Install Orbit Marine IC PRO LED 3
Cable Connections 4
Remote & Controller Overview 5
Controller Programming 7
Warranty & Safety Warnings 12
IMPORTANT: Please refer to additional safety warnings on last page.
- Carefully examine light fixture, wires and all components before and after installation. Ensure there is no
damage or water on any components BEFORE plugging into a GFCI wall outlet.
- NEVER plug in a wet cord. Always unplug with dry hands for any maintenance or service.
- Ensure 12VDC UL® transformer is plugged into a GFCI approved outlet with a drip loop for each light
fixture. If using eFlux wave or flow pumps, ensure a 24VDC UL
®
transformer is used with drip loop.
- Turn controller OFF and disconnect lights and pumps from power & GFCI outlet before performing service.
- Never look directly into the LEDs.
- Never run pumps dry or out of water.
- Follow all safety instructions for any eFlux wave or flow pumps or additional accessory add-ons.
- eFlux wave pumps create a tremendous amount of water flow. Do not install pump where the
strong current can harm corals or animals.
- eFlux wave pumps can produce powerful waves in both wave and surge modes. Ensure your aquarium is
designed for wave pumps and ensure pumps are mounted low enough not to push water out of the
aquarium tank.
- Ensure light fixture is kept clean of any saltwater or salt creep. Fixture is IP65 rated for water splashing
but must be kept clean of water, moisture, salt creep and/or any mineral deposits.
AC Power
GFCI Outlet
12VDC
Power Supply
LOOP®
Controller
Wave Pump
Manifold HUB
24VDC ONLY
P1P3
P2
12VDC
Power Supply
Drip
Loop
Drip
Loop
SAVE THESE INSTRUCTIONS
L1L2
LOOP® IC Light
Manifold HUB
12V DC ONLY
Orbit Marine PRO IC LED
eFlux Accessory
Wave Pump Add-on
Use caution when
installing magnets
Ensure pump location
will not spill water from
wave motion
Use only with GFCI
Protected AC Outlet
Keep fixture clean of
water and/or salt creep
Ensure use of drip
loop for all cables
Ensure use of drip
loop for all cables
Ensure correct voltage power
supply for each component
Thank You!
For purchasing our Orbit Marine IC PRO LED
Lighting system. Please read all instructions
before getting in the LOOP®!
Safety Instructions
Safety Instructions & Warnings
Table of Contents
Page 1
24VDC
Power Supply

Current Orbit Marine IC PRO LED Specifications

General

Brand	Current
Model	Orbit Marine IC PRO LED
Category	Lighting Equipment
Language	English

Summary

Safety Instructions & Warnings

General Safety Precautions

Covers essential safety guidelines for electrical and water use with the device.

Equipment Care and Handling

Details proper care, maintenance, and safe handling of the lighting system components.

What's Included

Recommended Accessories

eFlux Wave Pumps

Details compatible eFlux wave pumps for enhanced aquarium water flow control.

Controllable DC Flow Pumps

Lists controllable DC flow pumps to complement the lighting system.

Additional Accessories

Mentions optional accessories for system upgrades and mounting.

Installation Instructions

Fixture Installation

Guides on unpacking, mounting, and positioning the LED light fixture.

Controller and Manifold Hub Setup

Instructions for installing the LOOP IC Controller and Manifold Hub.

Cable Connection Overview

Introduces the process of connecting various system components via cables.

Cable Connections Guide

Connecting System Components

Detailed steps for connecting lights, pumps, controller, and sensors.

Power Supply and Cable Management

Guidance on connecting power supplies and organizing excess cables.

Remote Sensor and Power-Up

Instructions for setting up the IR sensor and initial power-on sequence.

LOOP® IC Remote Control Overview

Remote Button Functions

Explains the purpose and operation of each button on the wireless remote.

Wave Pump Programming Controls

Details how to program and control eFlux wave pumps using the remote.

Lighting Mode Controls

Covers programming color spectrums, dynamic modes, and weather effects.

LOOP® IC Controller Interface

Display Indicators and Modes

Describes the controller's display symbols, icons, and operational modes.

Light Cycle Diagram

Visual representation of the programmed daily light cycle including sunrise/sunset.

LOOP® IC Controller Programming - Basic

Powering Lights and Security

How to turn lights on/off and lock/unlock controller settings for security.

Setting Time and Daily Schedules

Instructions for setting the current time and daily ON/OFF schedules for the lights.

LOOP® IC Controller Programming - Lighting

Daily Weather Patterns

Steps to program and activate dynamic weather effects for the lighting.

Color Spectrum Configuration

Guides on setting custom color spectrums for daylight, sunrise, and moonlight.

LOOP® IC Controller Programming - Advanced

Custom Colors and Dynamic Modes

How to program custom colors and activate on-demand dynamic modes like clean or feed.

eFlux Wave Pump Operation

Details on controlling wave pumps including turning them on/off and setting feed mode.

eFlux Wave Pump Programming

Wave Pump Modes and Flow Rates

Explains Stream/Steady, Surge/Gyre, and Wave/Pulse modes for pumps.

LOOP® IC Controller Pump Settings

Flow, Frequency, and Designation

Adjusting water flow, frequency, and designating pumps as primary/secondary.

Resetting Controller Defaults

Procedure to reset the LOOP IC Controller to factory default settings.

Safety and Warranty Information

Critical Safety Warnings

Comprehensive safety warnings and important instructions for safe operation.

Product Warranty Details

Information on the one-year limited warranty and its terms.