curt 45832 - User Manual

CURTMFG.COM
•
NEED ASSISTANCE?
•
877.287.8634
•
45832-INS-RA
•
PAGE 1
INSTALLATION MANUAL
45832
WARNING
Do not modify this product in any way. Unauthorized modification may impair the
function and / or safety and could affect the life of the product and void the warranty.
Rated for 13,000 lbs. straight-line pull. Never exceed the rated capacity of the product,
vehicle's defined Gross Combined Weight Rating (GCWR) or hitch receiver rating.
Product is designed only for vehicle recovery and must not be used for towing.
CAUTION
Check for damaged parts before each use. Carefully check that the product
will operate properly and perform its intended function. Replace damaged
or worn parts immediately. Never operate the product with a damaged part.
NOTICE
Before you begin installation, read all instructions thoroughly.
To help prevent damage to the product or vehicle, refer to the specified
torque specifications when securing hardware during the installation process.
Reference vehicle owner's manual for weight ratings and capacities prior to use.
Maintenance
Inspect the unit for proper operation and worn, damaged or missing parts.
Replace as required or when the unit's wear exceeds 1/8" from the original surface.
Periodically apply a small amount of grease or anti-seize to the shackle bolt threads.
Installation Diagram
Product Photo
Tools Required
None
Torque Specifications
7/8" shackle bolt 30 lb-ft.
Use above torque setting unless otherwise noted
Level of Difficulty
Easy
Parts List
Qty Description
1 D-ring shackle mount, 2" shank
Hitch pin
Hitch pin & clip
sold separately
Receiver tube
2" shank
D-ring
shackle
Shackle bolt
Shackle bolt should be flush with
outside of shackle prior to use
Clip
Step 1
Slide the shank of the D-ring shackle
mount into your vehicle's 2" receiver
and align the hole in the shank with
the hole in the receiver hitch.
Insert your hitch pin (sold separately)
through the hitch and D-ring shank. Secure
on the opposite side with the clip provided
with your hitch pin. See diagram below.
Step 2
Secure your tow strap (sold separately) by
feeding it through the opening in the shackle.
Depending on the style and size of your
tow strap, it may be necessary to remove
the shackle from the shank. Remove the
shackle by loosening the shackle bolt and
reinstalling after hooking up the tow strap.
Note: Ensure the shackle bolt is fully
threaded into the shackle after removal
and reinstallation. Torque to 30 ft-lbs.
The end of the bolt should be flush with the
outside of the shackle when re-installed.
WARNING
Failure to fully tighten the shackle
bolt may result in loss of attachment,
property damage or personal injury.
Product Registration
CURT stands behind our products
with industry-leading warranties.
Provide feedback and help us to improve our
products by registering your purchase at:
warranty.curtgroup.com/surveys

Summary

Product Information

Level of Difficulty

Indicates the installation is straightforward and requires minimal expertise.

Parts List

Lists the main component: a 2-inch shank D-ring shackle mount.

Tools Required

Specifies that no special tools are needed for installation.

Torque Specifications

Shackle Bolt Torque

Specifies the torque setting for the 7/8-inch shackle bolt as 30 lb-ft.

Installation Instructions

Step 1: Mount Insertion

Slide the D-ring shackle mount shank into the vehicle's 2-inch receiver and align holes.

Step 2: Secure Tow Strap

Feed tow strap through shackle; may require removing shackle from shank.

Safety and Usage Warnings

General Warning

Warns against product modification and exceeding capacity ratings for recovery.

Caution: Part Inspection

Advise checking parts for damage before each use to ensure proper function.

Warning: Shackle Bolt Tightness

Warns that failure to fully tighten shackle bolt can cause attachment loss or injury.

Important Information

Notice: Read Instructions Thoroughly

Emphasizes reading all instructions and referring to vehicle manuals for ratings.

Maintenance Guidelines

Inspect for wear, replace damaged parts, and apply grease to shackle bolt threads.

Product Registration

Encourages product registration for warranty and feedback purposes.

Installation Diagram

Diagram Components

Illustrates key parts like receiver tube, shank, shackle bolt, and hitch pin.

curt 45832 Specifications

General

Product Type	Hitch
Hitch Class	Class III
Tongue Weight	600 lbs
Material	Steel
Installation	Bolt-On
Tongue Weight Capacity	600 lbs
Installation Type	Bolt-On
Towing Capacity	6000 lbs
Receiver Tube Size	2 inch
Finish	Black Powder Coat
Hitch Weight Capacity	6, 000 lbs
Hitch Tube Size	2 inch