Datamax A-Class A-4310 User Manual

A-Class 39
4.2.3 Printer Options
The Printer Options menu contains module, file handling, and option functions:
Menu Item Details
MODULES Controls module functions (see Appendix A), where:
PRINT DIRECTORY Prints files present and available memory in a module.
(Selecting ALL will print the results from every
module.)
PRINT FILE Displays a list of stored files then prints the selected
file image or name.
Selects from a list of modules available for formatting. FORMAT MODULE
All data in the selected module will be erased.
DELETE FILE
Deletes a file name, preventing further access.
(Protected modules will not appear.)
PACK MODULE
Reclaims all storage space associated with the deleted
files on the specified module.
CUTTER Controls the Cutter and queuing functions, where:
MODE
Sets the detection method and printer response,
where:
AUTO The presence of the cutter is automatically sensed. If
detected, the cutter is enabled; otherwise, it will be
ignored.
ENABLED
Enables the cutter. If the cutter is not detected, a fault
will be generated.
DISABLED
Disables the cutter.
CUT BEHIND
Allows a number of small labels to queue before a cut
is performed, increasing throughput, where:
; (1) Can be used without a cutter to allow the
presentation of an extra label, as retraction will not
be performed until the next job or feed.
(2) After a fault, the leading edge will be cut to
ensure material length.
0 (0 – 2)
Is the number of labels queued before cutting; see
Appendix A for details.

Datamax A-Class A-4310 Specifications

General

Print Resolution	203 dpi
Connectivity	USB, Serial, Ethernet
Max. Print Length	39 inches
Print Technology	Thermal Transfer
Label Length Range	0.5" to 39"

Summary

2 Getting Started

2.1 Unpacking

2.2 Installation

2.2.1 Mounting Requirements

2.2.2 Interfacing a Host

Explains how to connect the printer to a host system via parallel, serial, and USB ports.

2.2.2.1 Parallel Port Connections

2.2.2.2 Serial Port Connections

2.2.2.3 USB Port Connections

2.2.3 Connecting an Applicator

2.2.4 Connecting Power

3 Setting up the Printer

3.1 Loading Media

Step-by-step instructions for loading various types of media into the printer.

3.2 Adjusting the Media Sensor

Explains how to position and adjust the media sensor for accurate label detection.

3.3 Loading Ribbon

Provides instructions for loading thermal transfer ribbon based on printer model and ribbon orientation.

3.3.1 Right Hand Models

3.3.2 Left Hand Models

3.3.3 Removing Ribbon

3.4 Quick Calibration

Guides the user through the quick calibration process for optimal media detection.

3.5 Print Quality Controls

Explains how to adjust settings like HEAT and PRINT SPEED for print quality.

4 Using the Control Panel

4.2 The System Menu

Details the structure and navigation of the printer's system menu for configuration.

4.2.1 Media Settings

Covers menu options for configuring media type, sensor type, label length, and ribbon settings.

4.2.2 Print Control

Explains settings for print quality, throughput, and formatting like HEAT, PRINT SPEED, and CONTRAST.

4.2.3 Printer Options

Details configuration options for modules, file handling, cutter, ribbon saver, scanner, and barcodes.

4.2.4 System Settings

Covers settings for configuration files, modules, fonts, symbols, time/date, and printer identification.

4.2.5 Communications

Explains settings for serial, parallel, USB, and network interface ports for data communication.

4.2.6 Diagnostics

Describes diagnostic functions for testing printer options like cutters, ribbon savers, and GPIO.

4.2.7 MCL Options

4.3 The Test Menu

Explains how to access and use the test menu for printing various test labels.

4.3.1 Print Quality Label

4.3.2 Print Configuration

5 Operating, Adjusting and Maintaining the Printer

5.2 Calibration

Guides on performing printer calibration to ensure accurate media detection.

5.2.1 Standard Method

Step-by-step instructions for performing a standard calibration procedure for media.

5.2.2 Advanced Entry

Provides an alternate calibration method for special media types when standard calibration fails.

5.3 Printhead Adjustments

Explains how to adjust the printhead for consistent print quality.

5.3.1 Leveling Cam Adjustment

5.3.2 Burn Line Adjustment

5.4 Printhead Replacement

Step-by-step instructions for safely replacing the printer's printhead.

5.5 Maintenance Schedule

5.5.1 Cleaning the Printhead

5.5.2 Cleaning the Rollers

5.5.3 Cleaning the Peel Assembly

5.5.4 Cleaning the Media Sensor, Media Path, and Peel Bar

5.6 Reset Methods

Explains the three levels of printer reset: Soft, Level One, and Level Two.

5.6.1 Soft Reset

5.6.2 Level One Reset

5.6.3 Level Two Reset

5.7 Updating the Firmware

Guides on how to update the printer's application program (firmware).

5.8 Updating the Boot Loader

Provides instructions for updating the printer's boot loader program.

5.9 Downloading Fonts

6 Troubleshooting

6.1 Problem Resolution

Offers solutions for common printer problems that may not display specific error messages.

6.1.1 General Resolutions

6.1.2 Warning and Fault Messages

6.2 Hex Dump Mode

7 Specifications

7.1 Printer Specifications

7.2 Approved Media and Ribbon

Appendix B

Appendix F

Appendix G