Need help?Do you have a question about the dbx DriveRack 220i and is the answer not in the manual?
General| Brand | dbx |
|---|---|
| Model | DriveRack 220i |
| Category | Computer Hardware |
| Language | English |
General warnings, operational precautions, and environmental considerations for safe use of the equipment.
Compliance with FCC rules and handling of electromagnetic interference for optimal operation.
Specific instructions and warnings regarding the UK mains plug and fuse replacement.
Official declaration of the product's compliance with relevant safety and EMC directives.
An overview of the dbx 220i system, its purpose, and key features like AFS.
Procedures for obtaining technical support, warranty service, and product returns.
Explains the terms and conditions of the product warranty, including registration and coverage.
Details the rear panel connectors, power receptacle, and input/output connections.
Explains the front panel controls, display, LEDs, and meters for operation.
Guide on connecting the DriveRack 220i to audio sources, mixers, and amplifiers.
Instructions for installing the DriveWare GUI software on a computer.
Outlines the core philosophy of the 220i, focusing on program-based configuration and modules.
Steps for connecting the unit to a PC and launching the DriveWare GUI for operation.
Describes the three different views within the DriveWare GUI: Venue, Unit, and Module.
Explains how to change processing modules and link them within the unit's configuration.
Details how to edit processing module parameters, including saving changes.
Describes how to copy and paste parameters between modules and channels.
How to view input/output level meters and control output muting.
Instructions on how to load existing programs and store new configurations.
Procedures for saving and loading programs to and from a computer.
How to access and manage utility functions, such as program lists and system settings.
Explains how to use the DriveWare GUI in an offline mode for program creation.
Details how to configure communication preferences for the DriveWare GUI.
Configuration of input levels and routing for analog input channels.
Details the settings for the graphic equalizer (GEQ) and parametric EQ (PEQ) before the matrix.
In-depth explanation of the AFS module for automatic feedback elimination.
Description of the AGC module for maintaining consistent signal levels.
Parameters and operation of the dedicated De-Esser module for vocal sibilance.
Explanation of the Ducker module for attenuating one signal based on another.
Detailed parameters for the compressor module, including OverEasy and Ratio.
Configuration and parameters for the Noise Gate module to reduce background noise.
Information on using Notch Filters to remove specific undesirable frequencies.
Adjusting mix and output levels, and bypassing modules within the matrix mixer.
Details the 4-band parametric EQ available after the matrix mixer section.
Configuration of the Bandpass Filter module to adjust output bandwidth.
Parameters for the Limiter module, used for speaker and amplifier protection.
Settings for the delay module, including length and units.
Adjusting output level, polarity, and phase compensation for loudspeakers.
Details the Subharmonic Synthesizer module for enhancing bass frequencies.
Creating and managing custom program lists for sequential or restricted program access.
Configuring Zone Controllers for remote control of volume, mute, and program selection.
Enabling front panel lockout modes for security and preventing unauthorized changes.
A suggested application for mic processing and mixing using the DriveRack 220i.
Application guide for stereo or dual mono system processing with the DriveRack 220i.
Describes an application for room combining using the DriveRack 220i and ZC-4.
Application guide for background music and paging systems using the 220i.
Procedures for performing factory resets (soft/hard) and updating the unit's firmware.
Detailed technical specifications for the DriveRack 220i, including performance metrics.
A list and description of the factory-loaded programs available on the DriveRack 220i.
A block diagram illustrating the internal signal flow and components of the DriveRack 220i.
Instructions for configuring gain settings and relay bypass using internal jumpers.
Helpful tips, advanced techniques, and common troubleshooting advice for the DriveRack 220i.
Guidance on wiring and installing Zone Controllers, including different connection methods.
To Next Page
