To Next PageTo Next Page
Need help?Do you have a question about the Delta 31-260X and is the answer not in the manual?
Defines safety symbols (DANGER, WARNING, CAUTION) for hazard identification.
Ensure extension cords are in good condition and appropriately gauged for the machine.
Maintain a clean and well-lit work area to prevent accidents and injuries.
Take precautions against dust inhalation and skin contact to prevent serious health issues.
Machine is designed for wood only; sanding metal can cause fire or injury.
Avoid loose clothing, jewelry, and contain long hair to prevent entanglement.
Always disconnect power before making adjustments, repairs, or changing accessories.
Ensure the machine is properly grounded to protect the operator from electric shock.
Introduction to the 18" x 36" drum sander and its capabilities.
Lists all parts included in the shipping container for unpacking and assembly.
Instructions on how to unpack the machine and remove protective oil.
Step-by-step guide for assembling the stand for the drum sander.
Instructions for securely mounting the drum sander unit onto its assembled stand.
Guidance on installing and adjusting the leveling feet for stability.
Instructions on operating the main drum motor on/off switch.
Explanation of how to control the conveyor belt speed using the feed/speed switch.
Procedures for aligning the feed belt to prevent run-off.
Steps for setting the correct tension on the feed belt to prevent slippage.
Explains the use of different grit sandpaper for various sanding operations.
Discusses board width, type, and conveyor speed impact on sanding.
Information on when and how to switch between high and low drum speeds.
Advice for sanding face frames, panel doors, edges, and glued joints.
Addresses burn marks, stock size limits, and handling warped boards.
Guidance on table height adjustments and sanding multiple boards.
Procedure for adjusting the timing belt tension for smooth table movement.
Steps to ensure the table support plate is flat and parallel to the drum.
Instructions for cleaning, lubricating, and protecting the machine.
Tips for starting issues and protecting surfaces from rust.
Information on how to order identical replacement parts.
Information on obtaining service, repairs, and replacement warning labels.
Details on recommended accessories and the five-year limited product warranty.
Defines safety symbols (DANGER, WARNING, CAUTION) for hazard identification.
Ensure extension cords are in good condition and appropriately gauged for the machine.
Maintain a clean and well-lit work area to prevent accidents and injuries.
Take precautions against dust inhalation and skin contact to prevent serious health issues.
Machine is designed for wood only; sanding metal can cause fire or injury.
Avoid loose clothing, jewelry, and contain long hair to prevent entanglement.
Always disconnect power before making adjustments, repairs, or changing accessories.
Ensure the machine is properly grounded to protect the operator from electric shock.
Introduction to the 18" x 36" drum sander and its capabilities.
Lists all parts included in the shipping container for unpacking and assembly.
Instructions on how to unpack the machine and remove protective oil.
Step-by-step guide for assembling the stand for the drum sander.
Instructions for securely mounting the drum sander unit onto its assembled stand.
Guidance on installing and adjusting the leveling feet for stability.
Instructions on operating the main drum motor on/off switch.
Explanation of how to control the conveyor belt speed using the feed/speed switch.
Procedures for aligning the feed belt to prevent run-off.
Steps for setting the correct tension on the feed belt to prevent slippage.
Explains the use of different grit sandpaper for various sanding operations.
Discusses board width, type, and conveyor speed impact on sanding.
Information on when and how to switch between high and low drum speeds.
Advice for sanding face frames, panel doors, edges, and glued joints.
Addresses burn marks, stock size limits, and handling warped boards.
Guidance on table height adjustments and sanding multiple boards.
Procedure for adjusting the timing belt tension for smooth table movement.
Steps to ensure the table support plate is flat and parallel to the drum.
Instructions for cleaning, lubricating, and protecting the machine.
Tips for starting issues and protecting surfaces from rust.
Information on how to order identical replacement parts.
Information on obtaining service, repairs, and replacement warning labels.
Details on recommended accessories and the five-year limited product warranty.
General| Type | Oscillating Spindle Sander |
|---|---|
| Weight | 66 lbs |
| Motor | 120V, 1/4 HP |
| Spindle Speed | 1725 RPM |
| Oscillations Per Minute | 29 OPM |
| Spindle Stroke | 1 inch |
| Table Size | 14.75 x 14.75 inches |
| Speed | 1725 RPM |
| Spindle Sizes Included | 1/4, 1/2, 1-1/2 inches |
