Denon AVR-1705 Service Manual (English)

Other manuals for Denon AVR-1705

Service Manual75 pages

Product Sheet2 pages

Questions and Answers:

B
bowersveronicaJul 26, 2025
Why doesn't my Denon AVR-1705 Receiver remote control work properly?
- C
  Christian WalterJul 26, 2025
  Several reasons could explain this. First, check the batteries and replace them if they're dead. Ensure you're not too far from the unit; move closer. Check for any obstructions between the remote and the receiver and remove them. Make sure you're pressing the correct button. Finally, verify that the batteries are inserted correctly, with the < and > ends properly aligned.
D
David LaraJul 31, 2025
Why is there no sound from my Denon AVR-1705 Receiver even though the display is lit?
- C
  christyandrewsJul 31, 2025
  Several factors might be at play. First, ensure the speaker cords are securely connected. Next, check the INPUT SELECTOR knob to ensure it’s in the correct position. Also, verify that the volume control isn't set to the minimum. It's also possible that MUTING is enabled, so switch it off. Finally, if you've selected a digital input, make sure digital signals are being input or that you've selected the correct input jacks.
N
Nina MurrayAug 5, 2025
What to do if my Denon Receiver DISPLAY is not lit and no sound is produced?
- L
  Lori ThorntonAug 5, 2025
  First, check that the power supply cord is securely plugged in. If it is, try turning the power off with the remote control after turning the POWER switch on.
D
Dana SchmidtAug 9, 2025
How to fix reversed instrument positions during stereo playback on my Denon Receiver?
- J
  josephzamoraAug 9, 2025
  This issue is likely due to reversed connections. Check the left and right connections of both the speakers and the input/output cords to ensure they are correctly connected.
N
Nicole AdkinsAug 15, 2025
Why is the DISPLAY on my Denon AVR-1705 Receiver not displayed and the power indicator flashes rapidly?
- K
  Katrina NormanAug 15, 2025
  This issue may arise due to a short-circuit in the speaker terminals. To resolve this, switch off the power, properly connect the speakers, and then switch the power back on. Another potential cause is blocked ventilation holes. If this is the case, turn off the power, ensure adequate ventilation to cool down the unit, and then turn it back on. This issue can also happen if the unit is operating at continuous high power conditions with inadequate ventilation. Turn off the set’s power, then ventilate it well to cool it down. Once the set is cooled down, turn the power back on.
J
judithhendersonAug 20, 2025
What to do if sound is only coming from one channel on my Denon AVR-1705?
- J
  Jared HardyAug 20, 2025
  This could be due to incomplete connections. Make sure the speaker cords and input/output cords are securely connected.

Denon AVR-1705 Specifications

General

Speakers connectivity type	-
Receiver type	Surround
Frequency range	10 - 100000 Hz
Audio output channels	6.1 channels
Signal-to-Noise Ratio (SNR)	98 dB
Power output per channel (1KHz@6 Ohm)	110 W
Power output per channel (20-20KHz@8 Ohm)	75 W
Product color	Black
Audio decoders	DTS, DTS 96/24, DTS Neo:6, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), Dolby Digital, Dolby Digital EX
Digital Signal Processing (DSP)	Yes
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	56
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (typical)	230 W
Optical drive included	No
HDMI in	0
Composite video in	4
S-Video inputs quantity	3
Digital audio optical in	1
S-Video outputs quantity	2