Denon AVR-1912 User Manual

98
Input Setup
Video Default settings are underlined.
Set the source video.
z “BD”, “TV”, “GAME1” or “GAME2” can be set when “HDMI” (vpage 97) or “Component”
(vpage98) has been assigned.
Setting items Setting details
Video Select
Video of another input
source is played back
combined with the playing
audio.
SOURCE : Play the picture and sound of the input source.
BD / DVD / TV / SAT/CBL / GAME1 / GAME2 / V.AUX / DOCK : Select
video input source to view. This can be set for individual input sources.
“BD”, “TV”, “GAME1” and “GAME2” can be selected only when a
component video is assigned as an input source.
NOTE
•It is not possible to select HDMI input signals.
•Input sources for which “Delete” is selected at “Source Delete”
(vpage92) cannot be selected.
Video Mode
Make settings for video
processing.
BD
z
DVD TV
z
SAT/CBL GAME1
z
GAME2
z
V.AUX DOCK
Auto : Process video automatically based on the HDMI content
information.
Game : Always process video appropriate for game content.
Movie : Process video normally.
•If “Video Mode” is set to “Auto”, the mode is switched according to the
input contents.
•If a source is played in both MAIN ZONE (audio and video) and ZONE2
(audio only) modes in the same room, audio in MAIN ZONE and ZONE2
modes may sound out of synchronization, but this is not malfunction. In
this case, setting to “Game” mode may improve audio synchronization.
Setting items Setting details
Component
(Component video)
Set this to change the
component video input
connectors assigned to the
input sources.
BD DVD TV
SAT/CBL GAME1
GAME2 V.AUX DOCK
RCA
None : Do not assign a component video input connector to the selected
input source.
•At time of purchase, the settings of the different input sources are as
shown below.
Input source BD DVD TV SAT/CBL
Default
setting
None None None RCA
Input source GAME1
GAME2 V.AUX
DOCK
Default
setting
None None None None
•An input source to which an component video input connector cannot be
assigned is displayed as “– – –”.
•When a control dock for iPod is connected, signals cannot be assigned to
the component video connectors.
Default
The “Input Assign” settings
are returned to the default
settings.
Yes : Reset to the defaults.
No : Do not reset to the defaults.
If you select “Default” and press ENTER, the
message “Return settings to the default?”
is displayed. Select “Yes” or “No”, and then
press ENTER.
Basic version
Advanced version
Information
Advanced version
BD

Denon AVR-1912 Specifications

General

Impedance	47 Ω
Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	125 W
Power output per channel (20-20KHz@8 Ohm)	90 W
HDMI in	6
Composite video in	3
Component video (YPbPr/YCbCr) in	1
Headphone connectivity	6.3 mm
Connectivity technology	Wired
Speakers connectivity type	Banana connector/Binding posts
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
Ethernet LAN	Yes
AM band range	520 - 1710 kHz
FM band range	87.5 - 107.9 MHz
Supported radio bands	AM, FM
Preset stations quantity	56
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL
Display	-
Product color	Black
Audio decoders	Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-ES, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD
Apple docking compatibility	iPhone, iPod
AC input voltage	120 V
AC input frequency	60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	460 W

Weight and Dimensions

Depth	382 mm
Width	435 mm
Height	167 mm
Weight	10200 g