Denon AVR-2313 User Manual

3.4. DIAGNOSTIC MODE (Video/Audio (signal) path conrmation mode)
This mode is used for conrming the Video and Audio (signal) paths. (Troubleshooting)
Conrming the operation of unit can be easily done after repair.
Backup data will not be lost.
3.4.1. Starting diagnostic mode
Press the "Power operation (
X
)" button to turn on power while pressing the "ZONE2/REC SOURCE", "DIMMER" and "STATUS" buttons.
TUNED, STEREO and RDS are lit in FL display.(Refer to 29 page.)
3.4.2. Canceling diagnostic mode
Turn off the power by pressing the ON/Standby button.
3.4.3. Operation
Use the remote control (RC-1156) that is supplied with the AVRxx12 model. Press buttons on the remote control in the order indicated in the “Details of how to operate remote control” column in the following table to establish the conrmation path.
You will nd using another remote control unit with the macro functions very useful. To use the macro functions, program a macro function to output a remote control code in accordance with the steps in the table below.
3.4.4. Video system conrmation items
g.XX : Refer to the block diagram of the g.XXth.
Conrmation item Setting and display Details of how to operate remote controller *a)
Output sequence of remote control codes
※
It is useful to form a macro program. *b)
Contents of conrmation Remarks
1
Analog Video (signal) Path VIDEO Conversion : OFF
All ZONE : ON
Display:
V 0 1 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF ·Input : CVBS / Output : CVBS
·Input : USB (Picture) / Output : CVBS
·Input Component / Output : Component
·Input HDMI / Output : HDMI
(
b
As the input source, you can switch from DVD to other ones.)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [1/./]
w
KEY 1/CODE1 (Main Zone)
Initialization
6.Press [ZONE SELECT], Select "ZONE2"
7.Press [ZONE ON]
e
ZONE2 POWER ON
8.Press [ZONE SELECT], Select "MAIN"
9.Press [DVD]
r
DVD (Main Zone)
2
Analog or HDMI to HDMI (signal) Path VIDEO Conversion : ON
IP Scaler : Analog&HDMI
Resolution : Auto
Display:
V 0 2 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF ·Input CVBS / Output : HDMI
·Input Component / Output : HDMI
·Input HDMI / Output : HDMI
·Input : USB (Picture) / Output : HDMI
(
b
As the input source, you can switch from DVD to other ones.)
Conrm the input pass one by one.
Because it becomes only the input of the highest input
becomes Convert/ (signal) Path if it inputs it at the same
time.
(HDMI input > Component input > CVBS input)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [2/ABC]
w
KEY 2/ABC (Main Zone)
Initialization
6.Press [ZONE SELECT], Select "ZONE2"
7.Press [ZONE ON]
e
ZONE2 POWER ON
8.Press [ZONE SELECT], Select "MAIN"
9.Press [DVD]
r
DVD (Main Zone)
3
GUI FUNCTION VIDEO Conversion : ON
IP Scaler : Analog&HDMI
Resolution : Auto
Menu : ON
All ZONE :ON
Display:
V 0 2 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF ·GUI Display / Output : HDMI
(
b
As the input source, you can switch from DVD to other ones.)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [2/ABC]
w
KEY 2/ABC (Main Zone)
Initialization
6.Press [ZONE SELECT], Select "ZONE2"
7.Press [ZONE ON]
e
ZONE2 POWER ON
8.Press [ZONE SELECT], Select "MAIN"
9.Press [DVD]
r
DVD (Main Zone)
10.Press [AMP]
11.Press [MENU]
t
GUI MENU (Main Zone)
4
CEC FUNCTION
(Control Monitor : HDMI Monitor1)
HDMI Control : ON
Display:
V 0 3 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF · When the power supply of a TV is put in the standby mode, make sure
that the power supply of this unit is also put in the standby mode.
(
b
As the input source, you can switch from DVD to other ones.)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [3/DEF]
w
KEY 3/DEF (Main Zone)
Initialization & CEC Control ON &Control Monitor1
6.Press [DVD]
e
DVD (Main Zone)
5
CEC FUNCTION
(Control Monitor : HDMI Monitor2)
HDMI Control : ON
Display:
V 0 4 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF · When the power supply of a TV is put in the standby mode, make sure
that the power supply of this unit is also put in the standby mode.
(
b
As the input source, you can switch from DVD to other ones.)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [4/GHI]
w
KEY 4/GHI (Main Zone)
Initialization & CEC Control ON &Control Monitor2
6.Press [DVD]
e
DVD (Main Zone)
6
HDMI Audio (signal) Path
(Audio : AMP)
Audio : AMP(When checking the audio output
from AMP)
Display:
V 0 5 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF ·Input : HDMI (Signal of PCM, Dolby Digital or DTS) / Output : Speakers
·Input : HDMI (Signal of HD Audio) / Output : Speakers
(
b
As the input source, you can switch from DVD to other ones.)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [5/JKL]
w
KEY 5/JKL (Main Zone)
Initialization & Select Audio AMP
6.Press [DVD]
e
DVD (Main Zone)
7
HDMI Audio (signal) Path
(Audio : TV)
Audio : TV(When checking the audio output
from TV)
Display:
V 0 6 D V D
1.Press [AMP]
2.Press [ZONE SELECT] , Select "ZONE2"
3.Press [ZONE OFF]
q
ZONE2 POWER OFF · Input : HDMI (Signal of PCM or Dolby Digital or DTS) / Output : HDMI
(Audio output from connected TV)
(
b
As the input source, you can switch from DVD to other ones.)
4.Press [ZONE SELECT], Select "MAIN"
5.Press [6/MNO]
w
KEY 6/MNO (Main Zone)
Initialization & Audio Select TV
6.Press [DVD]
e
DVD (Main Zone)
s
g.1
g.2
g.3
g.4
g.5
g.6
g.7
31

Denon AVR-2313 Specifications

General

Receiver type	Surround
Frequency range	10 - 100000 Hz
Input sensitivity	200 mV
Pre-out connectivity	Yes
Audio output channels	7.1 channels
Audio A/D Converter (ADC)	24-bit/96kHz
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.08 %
Power output per channel (1KHz@6 Ohm)	135 W
Power output per channel (20-20KHz@8 Ohm)	105 W
HDMI in	6
Composite video in	4
USB ports quantity	1
Component video (YPbPr/YCbCr) in	2
Headphone connectivity	6.3 mm
Connectivity technology	Wired
Speakers connectivity type	Binding post
Wi-Fi	No
FM band range	87.5 - 108 MHz
Supported radio bands	FM
Optical drive included	-
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Product color	Black
Audio decoders	Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS 96/24, DTS Neo:6, DTS-HD
Volume control	Digital
Apple docking compatibility	iPod
Number of products included	1 pc(s)
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	600 W
Cables included	AC
Audio formats supported	FLAC, MP3, WAV, WMA

Weight and Dimensions

Depth	382 mm
Width	434 mm
Height	167 mm
Weight	10900 g