EasyManuals Logo

Denon AVR-X4000 Service Manual

Denon AVR-X4000
224 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #77 background imageLoading...
Page #77 background image
2. How to update by DPMS
You can update the rmware by downloading the latest version from the Internet.
2.1. Connecting to the Network
(1) System requirements
Internet Connection by Broadband Circuit
• Modem
Router
Ethernet cable (CAT-5 or greater recommended)
(2) Setting
2.2. Checking and updating the rmware
Check if the latest rmware exists. You can also check approximately time required to complete an update.
(1) Press the
"SETUP" button on the remote control to display the GUI menu.
(2) Use the cursor buttons to select
"General""Firmware""Update""Check For Update".
(3) Press the
"ENTER" button.
The latest version of the rmware on the website is displayed.
If the rmware on the website is latest, proceed to (4).
If the latest rmware has been already installed, press the
"SETUP" button to close the menu.
(4) Use the cursor buttons to select
"Start", then press the "ENTER" button.
During update, the power indicator lights in red and the GUI screen disappears. And an approximately remaining
time is indicated on the display.
When updating is complete the power indicator lights in green and normal status is resumed.
(5) Press the
"MENU" button to close the menu.
--- Cautions on Firmware Update ---
In order to update the rmware, you must have the correct system requirements and settings for a broadband Internet
connection.
Do not turn off the power until updating is completed.
Even with a broadband connection to the Internet, approximately 1 hour is required for the updating procedure to be
completed.
Once updating starts, normal operations on the this unit cannot be performed until updating is completed. Also, setting
items of the GUI menu of this unit or setting items of the image adjustment may be initialized.
Note down the settings before updating, and set them again after updating.
SIGNAL
GND
AM
CBL/
SAT
MEDIA
PLAYER
MEDIA
PLAYER
MEDIA
PLAYER
ZONE2
1 CBL
/
SAT
2 DVD
Y
P
B
/
CB
DVD
2
1
3
PR
/
CR
ZONE2 ZONE3 FRONT
Denon Link HD
CBL
/
SAT
AUDIO
TV
CD
DVD
COAXIAL OPTICAL
1
1
2
2
DIGITAL AUDIO
IN
DC12V
150mA
MAX.
STRAIGHT CABLE
1
2
RS-232C
REMOTE CONTROL
IR
IN OUT
TRIGGER OUT
1 CBL/SAT
2 DVD
3 Blu-ray
PHONO
3 Blu-ray
4 MEDIA PLAYER
1 CBL
/
SAT
2 DVD 5 CD
MONITOR
IN
VIDEO VIDEO
(
ASSIGNABLE
)
(
ASSIGNABLE
)
(
ASSIGNABLE
)
HDMI
IN
OUT
(
ASSIGNABLE
)
COMPONENT VIDEO
IN
IN
AUDIO
IN
AUDIO
(
ASSIGNABLE
)
OUT
AUDIO
FRONT
FRONT
SURROUND
SURROUND
CENTER
NETWORK
Modem
Internet
PC
LAN port/
Ethernet
connector
ETHERNET
connector
Router
To WAN port
To LAN port
To LAN port
77

Table of Contents

Other manuals for Denon AVR-X4000

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X4000 and is the answer not in the manual?

Denon AVR-X4000 Specifications

General IconGeneral
Receiver type-
Frequency range10 - 100000 Hz
Output impedance16 Ω
Speaker selectorA+B
Input sensitivity200 mV
Audio output channels7.2 channels
Signal-to-Noise Ratio (SNR)102 dB
Total Harmonic Distortion (THD)0.008 %
Power output per channel (1KHz@6 Ohm)165 W
Power output per channel (20-20KHz@8 Ohm)125 W
HDMI in7
AC (power) inYes
Composite video in4
Ethernet LAN (RJ-45) ports1
Component video (YPbPr/YCbCr) in2
Number of HDMI outputs3
Connectivity technologyWired
Speakers connectivity typeBanana connector
Audio formats supportedAAC, FLAC, MP3, WAV, WMA
Image formats supportedJPG
Wi-FiNo
RDS featuresPTY, TP
FM band range87.5 - 108 MHz
Supported radio bandsFM
Internet radio services supportedSpotify, vTuner
Supported video modes1080i, 1080p, 480p, 576p, 720p
DisplayVFL
Color depth24 bit
Aspect ratio4:3, 16:9
Product colorSilver
Audio decodersDolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic II, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS-ES (Discrete 6.1), DTS-ES (Matrix 6.1), DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantityUSB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibilityNot supported
AC input voltage230 V
AC input frequency50 - 60 Hz
Power consumption (standby)0.1 W
Power consumption (typical)670 W
Weight and Dimensions IconWeight and Dimensions
Depth379 mm
Width434 mm
Height167 mm
Weight12300 g

Related product manuals