Denon AVR-X2000 - User Manual

Other manuals for Denon AVR-X2000

Service Manual196 pages

Getting Started10 pages

Manual10 pages

Questions and Answers

T
Theresa WoodJul 26, 2025
What to do if the Denon AVR-X2000 power turns off and the power indicator flashes red every 0.5 seconds?
- B
  Blake LunaJul 26, 2025
  If your Denon Receiver's power turns off and the power indicator flashes red every 0.5 seconds, it could be due to a few reasons. First, the protection circuit may have been activated because speaker cable core wires are in contact. Unplug the power cord and re-twist the core wire or take care of the connector, then reconnect the wire. Alternatively, try turning down the volume and turning the power on again. If the issue persists, the unit’s amplifier circuit may have failed, unplug the power cord and contact our customer service center.
E
ethanrodriguezJul 31, 2025
Why does my Denon AVR-X2000 Receiver remote control not work?
- B
  Brianna DixonJul 31, 2025
  If your Denon Receiver remote control isn't working, try the following: * Replace the batteries with new ones. * Ensure you're within 7 meters and a 30° angle of the unit. * Remove any obstacles between the remote and the unit. * Verify the batteries are inserted correctly, checking the + and - marks. * Move the unit away from strong light sources like direct sunlight or inverter-type fluorescent bulbs. * Press MAIN or ZONE2 to select the correct zone. * Adjust the direction and distance of 3D video devices to prevent interference.
B
Blake SmithAug 5, 2025
What to do if Denon AVR-X2000 Receiver power turns off and the power indicator flashes red every 2 seconds?
- A
  ashleyperezAug 5, 2025
  If your Denon Receiver's power turns off and the power indicator flashes red approximately every 2 seconds, the protection circuit may have been activated due to a rise in temperature. Turn the power off, wait about an hour for the unit to cool down, and then turn it on again. Also, ensure the unit is installed in a place with good ventilation.
D
Debra MillerAug 10, 2025
How do I fix a Denon AVR-X2000 Receiver display that is off?
- W
  William AveryAug 10, 2025
  If your Denon Receiver display is off, set “Dimmer” on the menu to something other than “Off.” When the sound mode is set to PURE DIRECT, the display is off.
K
Kelsey EverettAug 15, 2025
Why does my Denon AVR-X2000 Receiver power automatically turn off?
- T
  thomasjensenAug 15, 2025
  Your Denon Receiver might be automatically turning off because the sleep timer is set. In this case, turn the power on again. Alternatively, “Auto Standby” may be enabled. To disable it, set “Auto Standby” on the menu to “Off.”
S
Stephen PatelAug 20, 2025
How to turn off Denon Receiver when the display shows “Main Zone Off”?
- M
  Mary TerryAug 20, 2025
  If your Denon Receiver power does not turn off even when the power button is pressed, and the display shows “Main Zone Off”, it means the power in either ZONE2 is on. To turn the power of the unit off (standby), either press the ZONE2 ON/OFF button on the unit, or press the ZONE2 button on the remote control and then press the POWER X button to turn the ZONE2 power off.

Denon AVR-X2000 Specifications

General

Receiver type	-
Frequency range	10 - 100000 Hz
Output impedance	16 Ω
Input sensitivity	200 mV
Audio output channels	7.1 channels
Signal-to-Noise Ratio (SNR)	100 dB
Power output per channel (1KHz@6 Ohm)	125 W
Power output per channel (20-20KHz@8 Ohm)	95 W
HDMI in	7
AC (power) in	Yes
Audio (L/R) in	4
Composite video in	2
Component video (YPbPr/YCbCr) in	1
Connectivity technology	Wired
Speakers connectivity type	Banana connector
Audio formats supported	AAC, FLAC, MP3, WAV, WMA
Image formats supported	JPG
Wi-Fi	No
RDS features	PTY, TP
FM band range	87.5 - 108 MHz
Supported radio bands	FM
Internet radio services supported	Spotify, vTuner
Supported video modes	1080i, 1080p, 480p, 576p, 720p
Display	VFL
Color depth	24 bit
Aspect ratio	4:3, 16:9
Product color	Black
Audio decoders	Dolby Digital, Dolby Digital EX, Dolby Digital Plus, Dolby Pro Logic IIx, Dolby Pro Logic IIz, Dolby TrueHD, DTS, DTS-ES, DTS-HD, DTS-HD Master Audio
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Apple docking compatibility	Not supported
AC input voltage	230 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.1 W
Power consumption (typical)	500 W