Error
Code
Details of Error code Display Coping strategies
5B
NACK was received when "L"
command sent to Sub CPU, DSP,
PLD etc.
S u b * * * m i n
U p d a t i n g f a i l 5 B
Turn off and on the power. Updating
starts automatically.
5C
Sub CPU, DSP, PLD etc. failed to
receive rmware for rewriting sent
from DM860A (when timed out).
S u b * * * m i n
U p d a t i n g f a i l 5 C
Turn off and on the power. Updating
starts automatically.
5D
Sub CPU, DSP, PLD etc. failed
to receive rmware for rewriting
sent from DM860A (when an error
occurred).
S u b * * * m i n
U p d a t i n g f a i l 5 D
Turn off and on the power. Updating
starts automatically.
5E
Data in rmware such as Sub CPU,
DSP and PLD for rewriting sent
from DM860A was invalid (when a
Check Sum error occurred).
S u b * * * m i n
U p d a t i n g f a i l 5 E
Turn off and on the power. Updating
starts automatically.
5F
Invalid data in rmware such as Sub
CPU, DSP and PLD for rewriting
sent from DM860A was invalid
(invalid data was received).
S u b * * * m i n
U p d a t i n g f a i l 5 F
Turn off and on the power. Updating
starts automatically.
60
NACK was received when "P"
command sent to Sub CPU, DSP,
PLD etc.
S u b * * * m i n
U p d a t i n g f a i l 6 0
Turn off and on the power. Updating
starts automatically.
61
NACK was received when "I"
command sent to Sub CPU, DSP,
PLD etc.
S u b * * * m i n
U p d a t e C h e c k N G 6 1
Turn off and on the power. Updating
starts automatically.
62
Start of Sub µ-com fail.
S u b * * * m i n
U p d a t i n g f a i l 6 2
Turn off and on the power. Updating
starts automatically.
80
Acquisition of serial ash data failed
before serial ash was deleted.
G U I * * * m i n
U p d a t i n g f a i l 8 0
Turn off and on the power. Updating
starts automatically.
81
Deleting data failed before serial
ash was rewritten.
G U I * * * m i n
U p d a t i n g f a i l 8 1
Turn off and on the power. Updating
starts automatically.
82
Receiving rmware for rewriting
serial ash sent by DM860A failed
(when timed out).
G U I * * * m i n
U p d a t i n g f a i l 8 2
Turn off and on the power. Updating
starts automatically.
83
Receiving rmwarefor rewriting
serial ash sent by DM860A failed
(when an error).
G U I * * * m i n
U p d a t i n g f a i l 8 3
Turn off and on the power. Updating
starts automatically.
84
Receiving rmwarefor rewriting
serial ash sent by DM860A failed
(when a Check Sum error).
G U I * * * m i n
U p d a t i n g f a i l 8 4
Turn off and on the power. Updating
starts automatically.
85
Receiving rmwarefor rewriting
serial ash sent by DM860A failed
(when invalid data was received).
G U I * * * m i n
U p d a t i n g f a i l 8 5
Turn off and on the power. Updating
starts automatically.
86
The data verication was invalid
after serial ash was rewritten.
G U I * * * m i n
U p d a t i n g f a i l 8 6
Turn off and on the power. Updating
starts automatically.
A0
Acquisition of (Application Mode)
IP address failed before rewriting
DM860A was rewritten (AutoIP).
E t h e r I M G * * * m i n
C o n n e c t i o n F a i l A 0
Check the network connection.
Carry out the update in an environment
that has little network load.
81
To Next Page
Loading...
Need help?
General
Weight and Dimensions
