Denon DRA-265R - Troubleshooting and Specifications; Problem Resolution Guide; Technical Performance Data; Component Specifications

DISPLAY
@ TUNED indicator
This lights when a station is properly tuned in.
@ STEREO indicator
This lights when receiving stereo broadcasts. It remains off when
receiving AM broadcasts.
@ AUTO indicator
This indicates the tuning mode. It lights in the auto mode and
remains off in the manual mode.
Using the Various Functions
1. Presetting stations in the memory
The frequency and the name of the radio station which you have input
yourself are also stored in the memory.
How to preset the memory
Press the MEMORY button ®. The “MEMO?” indicator on the display
@ lights. Next use SHIFT button ® to select the memory block A, B,
C, Dor E. Now press the PRESET UP or DOWN button @ to specify
the preset channel number, and then press the MEMORY button ®to
store the station in the memory.
The preset channel numbers for the different memory blocks are as
follows.
Memory block A: 1to8
Memory block B: 1to8
Memory block C: 1to8
Memory block D: 1108
Memory block E: 1to8
2. Auto Memory (FM only)
The DRA-265 is equipped with an auto memory function.
Connectthe antenna, setit so that stations can be received, then hold
inthe MEMORY button and press the POWER button to turn the power
on. Stations for which the auto stop function operates are stored inthe
preset memory in the order A1 to A8, B1 to B8, and soon, through E8.
Channel A1 is tuned in after the auto memory operation is completed.
Using this function makes it possible to find out the overall reception
conditions of the receivable stations. The memory can be used
effectively by recalling the channelsin the preset memory and replacing
stations whose reception is poor with stations whose reception is good,
using the procedure described in 1 above.
Table of characters
ENGLISH
@ MEMO indicator
This indicator lights for approximately 10 seconds when the
MEMORY button has been pressed and a station can be stored on
a PRESET CHANNEL button.
This flashes continuously during the auto memory operation.
® CH indicator
This lights when the preset channel number and shift mode (A, B, C,
D or E) are displayed.
(24) TAPE indicator
The TAPE indicator lights when the TAPE sourceis selected with the
tape selector buttons.
® Multi function display
This displays the frequency, station name, program type, etc.
3. Recalling preset stations
Use the SHIFT button ® to select memory block A, B, C, D or E, then
press the PRESET UP or DOWN button ® to recall the station stored in
the memory.
If the PRESET UP or DOWN buttons are pressed without pressing the
SHIFT button ®, the stations are recalled in the order A1 to A8, B1 to B8,
and so on, through E8.
. Writing station names
Youcan write in station names yourself (up to 8 characters). (Refer to the
table of characters on shown below.).
Operation Display
1. Press the CHARACTER button — First character flashes.
once.
2. Use the TUNING UP and
DOWN buttons ® to
select the desired
characters.
3. Use the SHIFT button ®
to move to the next
place.
4. After writing the entire
station name, store it
in the memory.
(Refer to page 8.)
First letter flashes.
Specified place flashes.
. Clearing station names
1. Recall the station name you want to clear.
2. Press the CHARACTER button once, the character at the first place
flashes.
3. Then press the SHIFT button for at least 2 seconds. The current
station name will then be cleared.
Note: Station names mustbe stored in apreset memoryto be retained. Ifthe
power is turned off, or if the band (AM/FM) is changed, the station
name will be lost. Be sure to store the entered station name ina Preset
Memory before changing the band or turning the power switch OFF.
The characters are input in the order shown to the right. Use the
TUNING buttons ® to select the desired characters.
A
CBEFGHIJKLMNOPHRST
iti7il
7
U W
“a
XY
/ 2 SPACE
DTA Ee PATER R Fe ome OP eee em eS eT