To Next PageTo Next PageWhy is my Denon Stereo Receiver POWER LED on but there is no sound?
If your Denon Stereo Receiver's POWER LED is on but you're not getting any sound, check the speaker cords to ensure they are securely connected. Also, verify that the INPUT SELECTOR is set to the correct position and that the VOLUME control is turned up to an audible level.
Why is sound only coming from one side of my Denon Stereo Receiver?
If you're only getting sound from one side of your Denon Stereo Receiver, start by checking the speaker cords and input cords to ensure they are securely connected. Then, adjust the BALANCE control to ensure it's properly set.
What to do if my Denon DRA-F101 Stereo Receiver remote control is not working?
If your Denon Stereo Receiver isn't responding to the remote, first, try replacing the batteries with new ones. If that doesn't work, make sure you're not too far from the unit and that there's nothing blocking the signal. Ensure you're pressing the correct button and that the batteries are inserted with the correct polarity.
How to stop booming sound when playing records on Denon DRA-F101 Stereo Receiver?
To address a booming sound when playing records on your Denon Stereo Receiver, first, ensure the turntable’s ground wire is securely connected. Next, check that the input cords are properly connected to the PHONO terminals. Finally, consider if there's interference from nearby electrical devices like a TV, and if so, change the installation position.
Why is there a hissing noise when tuning into FM stations on my Denon Stereo Receiver?
If you're hearing a hissing noise when tuning into an FM station on your Denon Stereo Receiver, make sure the antenna cable is properly connected. Also, check for interference from electronic devices with microprocessors or a weak FM signal. Try repositioning the equipment, connection cords, or antenna. Consider connecting an outdoor antenna.
What causes inverted instrument positions on my Denon DRA-F101?
To fix inverted instrument positions on your Denon Stereo Receiver for stereo sources, check the left and right speaker or input cord connections to ensure they are not inverted.
What to do if Denon DRA-F101 Stereo Receiver produces howling when playing records?
If you experience howling when turning up the volume while playing records on your Denon Stereo Receiver, the turntable and speaker systems might be too close. Move the speaker systems as far away as possible. Additionally, if the floor is soft and vibrates easily, use cushions to absorb vibrations transmitted from the floor to the speakers. If your turntable lacks insulators, consider using audio insulators.
Why won't my Denon DRA-F101 Stereo Receiver turn on?
If your Denon Stereo Receiver's POWER LED doesn't light up and no sound is produced when you turn on the power switch, make sure the power supply cord is properly connected.
How to eliminate scratchy noise when tuning AM on my Denon DRA-F101 Stereo Receiver?
To address a scratchy or hissing noise when tuning into an AM station on your Denon Stereo Receiver, check for interference from a TV set or another broadcast station. Try turning off the TV, changing the position or direction of the AM antenna, or connecting an outdoor antenna.
How do I stop humming noise on my Denon DRA-F101 when using AM?
To resolve a humming noise when tuning into an AM station on your Denon Stereo Receiver, try inserting the power plug in the opposite direction. Additionally, consider connecting an outdoor antenna.
General| Number of Channels | 2 |
|---|---|
| Frequency Response | 10 Hz - 100 kHz |
| Signal-to-Noise Ratio | 100 dB |
| Input sensitivity | 200 mV |
| Power consumption | 120 W |
| Total Harmonic Distortion (THD) | 0.1% |
| Input Impedance | 47k ohms |
| FM Tuning Range | 87.5 - 108 MHz |
| AM Tuning Range | 522 - 1611 kHz |
Safety check before unit return to customer.
Rated output power and output terminals.
Rated output, input sensitivity, impedance, RIAA deviation.
SN ratio, frequency response, tone control range.
Reception frequency, sensitivity, isolation, S/N, distortion.
Clock system, precision, timer functions.
Power supply, consumption, dimensions, net mass.
Remote system, power, dimensions, mass.
Procedure to remove the top cover.
Steps to remove the front panel assembly.
Detaching display and encoder boards.
Removing the system connector circuit board.
Procedure to disconnect and remove the tuner pack.
Removing the power board and heat sink.
Removing shield plate, back panel, and main PWB.
Procedure for setting and adjusting the idling current.
Diagram showing signal connections for testing.
Pinout and function for the main IC.
Layout and mapping of the FL display segments.
Pinout description for the FL display connector.
Anode connection mapping for display modes.
List of semiconductor components on the PWB.
List of resistors with part numbers and values.
List of capacitors with part numbers and specifications.
Components and assemblies for the DRA PWB.
List of all screws and nuts used in assembly.
List of packaging parts and accessories.
Detailed schematic for the main control and processing unit.
Schematic for the system control unit.
Schematic for the power amplifier section.
Detailed schematic for the front panel display and control interface.
Schematic for the volume encoder unit.
Schematic for the function encoder unit.
