EasyManua.ls Logo

Desoutter ESP-C 110 V - User Manual

Desoutter ESP-C 110 V
188 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Part no 6159934960
Issue no 06
Date 05/2020
Page 1 / 188
www.desouttertools.com
ESP-C Controllers
WARNING
WARNING
Read all safety warnings (including the ones of the separately provided safety
instructions n° 6159931790) and all instructions. Failure to follow the warnings and
instructions may result in electric shock, re and/or serious injury.
Save all warnings and instructions for future reference.
1
AVERTISSEMENT
Lire l'ensemble des mises en garde de sécurité (y compris celles sur la notice de
sécurité n° 6159931790 fournie à part) ainsi que l'ensemble des consignes. Le non-
respect des mises en garde et des consignes peut entraîner un choc électrique, un
incendie ou des blessures graves.
Conserver l'ensemble des mises en garde et consignes pour pouvoir les consulter
ultérieurement.
9
ADVERTENCIA
Lea todas las advertencias de seguridad (incluyendo las contenidas en las
instrucciones de seguridad n° 6159931790 suministradas por separado) y las
instrucciones. El incumplimiento de las instrucciones y advertencias de seguridad
puede producir descargas eléctricas, incendios y/o lesiones personales graves.
Guarde todas las instrucciones y advertencias para futuras consultas.
17
WARNUNG
Alle Sicherheitshinweise (einschließlich der separat bereitgestellten
Sicherheitsvorschriften Nr. 6159931790) und alle Anweisungen lesen. Eine
Nichtbeachtung der Hinweise und Anweisungen kann zu Stromschlägen, Bränden
und/oder schweren Personenschäden führen.
Bewahren Sie alle Warnhinweise und Anweisungen zur künftigen Verwendung auf.
25
Model Part number
ESP-C 110 V 6151654840
ESP-C 220 V 6151654800
ESP-C LT 110 V 6151654850
ESP-C LT 220 V 6151654810

Table of Contents

Questions and Answers

  • A
    April StewartAug 8, 2025
    What to do if Desoutter ESP-C 110 V motor is not detected?
    • K
      kenneth10Aug 8, 2025
      If the motor is not detected and the tool is not connected, check the cable and the connection between the screwdriver and the Desoutter Controller.
  • L
    Laura HoffmanAug 12, 2025
    What to do if Desoutter Controller shows bus undervoltage?
    • M
      Matthew GonzalesAug 12, 2025
      If the Desoutter Controller shows bus undervoltage, ensure that it is properly connected to a 110/230 VAC power supply, according to your country's standards.
  • K
    Kenneth AllenAug 17, 2025
    What to do if Desoutter ESP-C 110 V overloads power stage of torque measuring circuit (higher than 10 A)?
    • M
      Matthew HillAug 17, 2025
      If the power stage of the torque measuring circuit is overloaded (higher than 10 A for at least 600 ms), decrease the cycle rate and avoid reaching the stall torque of the motor connected to the Desoutter Controller.
  • M
    Marc StewartAug 21, 2025
    What to do if Desoutter ESP-C 110 V Controller overloads power stage of torque measuring circuit to 14.5 A?
    • M
      Mr. Joseph JenkinsAug 21, 2025
      If the power stage of the torque measuring circuit overloads to 14.5 A during at least 10 ms, decrease the cycle rate and avoid reaching the stall torque of the motor when using the Desoutter Controller.
  • T
    Tyler TurnerAug 25, 2025
    What to do if Desoutter ESP-C 110 V Controller is adjusted on the "soft" joint when it is a "hard" joint?
    • C
      Cynthia NunezAug 26, 2025
      If the Desoutter Controller is adjusted for a soft joint when it should be a hard joint, turn off the controller, wait 5 seconds, and then turn it back on. After restarting, verify the joint type setting.
  • T
    Traci WashingtonAug 30, 2025
    What to do if Desoutter ESP-C 110 V Controller is adjusted on the "hard" joint when the joint is "soft"?
    • E
      Eric CastilloAug 30, 2025
      If the Desoutter Controller is adjusted for a hard joint when the joint is soft, turn off the controller and turn it back on after 5 seconds. Then, check the type of joint setting.
  • R
    Richard MorrisSep 3, 2025
    How to fix no connection between main card and display on Desoutter ESP-C 110 V?
    • D
      danielle58Sep 3, 2025
      If there is no connection between the main card and the display on the Desoutter Controller, check that the flat jumper is well connected.

Desoutter ESP-C 110 V Specifications

General IconGeneral
BrandDesoutter
ModelESP-C 110 V
CategoryController
LanguageEnglish

Related product manuals