INSIDE CORNER:
Left side
1. Miter right at 45°
2. Save the right side of cut
Right side
1. Miter left at 45°
2. Save left side of cut
OUTSIDE CORNER:
Left side
1. Miter left at 45°
2. Save right side of cut
Right side
1. Miter right at 45°
2. Save left side of cut
Special Cuts
NEVER MAKE ANY CUT UNLESS THE MATERIAL IS
SECURED ON THE TABLE AND AGAINST THE FENCE.
Aluminum Cutting:
Certain workpieces, due to their size, shape or surface
finish, may require the use of a clamp or fixture to prevent
movement during the cut. Position the material so that you
will be cutting the thinnest cross section, as shown in
Figure 26. Figure 27 illustrates the wrong way to cut these
extrusions. Use a wax lubricant when cutting aluminum
such as Johnson’s Stick Wax No. 140. Apply the stick wax
directly to the saw blade before cutting. Never apply stick
wax to a moving blade.
The wax, available at most hardware stores and industrial
mill supply houses, provides proper lubrication and keeps
chips from adhering to the blade.
Be sure to properly secure workpiece. Refer to page 3 for
correct saw blade.
Bowed Material:
When cutting bowed material always position it as shown
in Figure 28 and never like that shown in Figure 29.
Positioning the material incorrectly will cause it to pinch the
blade near the completion of the cut.
Cutting Plastic Pipe or Other Round Material
Plastic pipe can be easily cut with your saw. It should be
cut just like wood and CLAMPED OR HELD FIRMLY TO
THE FENCE TO KEEP IT FROM ROLLING. This is
extremely important when making angle cuts.
Cutting Large Material
Occasionally you will encounter a piece of wood a little
too large to fit beneath the blade guard. A little extra height
can be gained by rolling the guard up out of the way, as
shown in Figure 24. Avoid doing this as much as possible,
but if need be, the saw will operate properly and make the
bigger cut. NEVER TIE, TAPE, OR OTHERWISE HOLD
THE GUARD OPEN WHEN OPERATING THIS SAW.
12
English
Maintenance
1. All bearings are sealed. They are lubricated for life
and need no further maintenance.
2. Periodically clean all dust and wood chips from around
AND UNDER the base and the rotary table. Even
though slots are provided to allow debris to pass
through, some dust will accumulate.
3. The brushes are designed to give you several years of
use. If they ever need replacement follow the
instructions on page 6 or return the tool to the nearest
service center for repair. A list of service center
locations is packed with your tool.
Repairs
To assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment (including brush inspection
and replacement) should be performed by authorized
service centers or other qualified service organizations,
always using identical replacement parts.
Full Warranty
DEWALT heavy duty industrial tools are warranted for one
year from date of purchase. We will repair, without charge,
any defects due to faulty materials or workmanship. For
warranty repair information, call 1-800-4-D
EWALT. This
warranty does not apply to accessories or damage caused
where repairs have been made or attempted by others. This
warranty gives you specific legal rights and you may have
other rights which vary in certain states or provinces.
In addition to the warranty, D
EWALT tools are covered by
our:
30 DAY NO RISK SATISFACTION GUARANTEE
If you are not completely satisfied with the performance of
your DEWALT heavy duty industrial tool, simply return it to
the participating seller within 30 days for a full refund.
Please return the complete unit, transportation prepaid.
Proof of purchase may be required.
FREE WARNING LABEL REPLACEMENT: If your
warning labels become illegible or are missing, call 1-800-
4-D
EWALT for a free replacement.
FIG. 28
FIG. 29
RIGHT
WRONG
FIG. 27
BLADE
FENCE
WRONG
To Next Page
Loading...
