To Next PageTo Next PageWhy does my Dimplex XLF10017-XD trip the circuit breaker?
If your Dimplex Indoor Fireplace trips the circuit breaker or blows a fuse when turned on, it might be due to an improper circuit current rating. To resolve this, install the unit on a dedicated minimum 15 amp circuit.
What to do if my Dimplex XLF10017-XD Indoor Fireplace doesn't turn on with the remote?
If your Dimplex Indoor Fireplace isn't responding to the remote control, here are a few things to check: * **Batteries:** Ensure the batteries in the remote are new and installed correctly, with the + side facing up. * **Remote:** If the batteries aren't the issue, the remote control itself may be defective and need replacement. * **IR Receiver:** A defective IR receiver could also be the problem, consider replacing the hidden touch controls.
How to fix a Dimplex Indoor Fireplace that won't turn on with touch controls?
If your Dimplex Indoor Fireplace isn't turning on using the manual touch controls, consider the following potential causes: * **Power Supply:** Ensure the unit is correctly wired, check the main disconnect panel, and verify that the wall switch is on (if applicable). * **Front Glass:** If the front glass was installed after the unit was powered on, turn off the power (from the breaker or outlet), install the front glass, and then turn the power back on. * **Touch Controls:** The hidden touch controls may be defective and require replacement. * **Main Control Board:** A defective main control board might be the cause, necessitating its replacement. * **Relay Board:** Similarly, a defective relay board could be the issue, requiring replacement.
Why won't the heater on my Dimplex Indoor Fireplace turn on?
If the heater on your Dimplex Indoor Fireplace isn't turning on, it could be due to these reasons: * **Heater Disabled:** The heater might be disabled. To enable or disable the heat function, press and hold the indicated buttons on the hidden touch controls simultaneously for 3 seconds. * **Permanently Disabled:** The heater may have been permanently disabled. If you want to use the heat function, install a jumper on the main board (if available) or purchase a new main board.
Why is my Dimplex XLF10017-XD Indoor Fireplace heater on but not producing heat?
If your Dimplex Indoor Fireplace's heater is on but not producing heat, there could be a couple of reasons: * **Normal Operation:** There's a normal 30-second delay before the heater starts producing heat, so wait briefly. * **Thermostat Setting:** The thermostat setting might be below the ambient temperature. Increase the thermostat setting to be above the ambient temperature.
Why does the circuit breaker trip when I turn on my Dimplex XLF10017-XD?
If the circuit breaker trips or a fuse blows when you turn on your Dimplex Indoor Fireplace, it might be due to an improper circuit current rating. To resolve this, install the unit on a dedicated circuit with a minimum 15 amp rating.
How to fix Dimplex Indoor Fireplace that does not turn on?
If your Dimplex Indoor Fireplace does not turn on with the manual touch controls, the issue might be due to a lack of incoming power. Ensure the unit is wired correctly, check the main disconnect panel, and verify that the wall switch is on (if applicable).
What to do if Dimplex Indoor Fireplace remote control not working?
If your Dimplex Indoor Fireplace doesn't turn on with the remote control, the batteries in the remote may be dead or installed incorrectly. Replace the remote control battery, ensuring it is installed with the + side facing up.
General| Model | XLF10017-XD |
|---|---|
| Type | Electric Fireplace |
| Voltage | 120V |
| Wattage | 1500W |
| Heating Area | 400 sq. ft. |
| Adjustable Thermostat | Yes |
| Remote Control | Yes |
| Finish | Black |
| Mounting Location | Indoor |
| Fuel Type | Electric |
| Material | Steel, Glass |
| Installation | Wall-mounted |
