Why is light leaking around the log set of my Dimplex Indoor Fireplace?
If light is leaking out around the log set of your Dimplex Indoor Fireplace, it's likely that the log set is not positioned properly in the unit. Consult the instructions for replacing the log set and ensure it is connected to the base panel.
What to do if my Dimplex XHD26L does not turn on using the manual controls?
If your Dimplex Indoor Fireplace isn't turning on with the manual controls, several factors could be at play. First, ensure the unit is not plugged into a power bar, surge protector, or extension cord. Check the fuse/breaker panel to ensure there is incoming power from the electrical wall socket. Other potential issues include a defective main control board, touchpad, or power supply, as well as a loose touchpad connection. In such cases, consider replacing the main control board, touchpad, or power supply and checking the touchpad connection.
What to do if my Dimplex XHD26L Indoor Fireplace does not respond to the remote control?
If your Dimplex Indoor Fireplace isn't responding to the remote, the batteries might need replacing. You can change the batteries. Alternatively, the remote control or touchpad could be defective, requiring replacement.
Why is the flame not visible on my Dimplex XHD26L?
If the flame is not visible on your Dimplex Indoor Fireplace, it could be due to several reasons. If you have log models, ensure the color theme is not set to t0, as the flame might be turned off. Another cause could be a defective flame LED strip or a defective main control board, in which case you should replace the flame LED strip or the main control board.
Why is the media not illuminated on my Dimplex Indoor Fireplace?
If the media in your Dimplex Indoor Fireplace is not illuminated, it could be because the unit is set to midnight mode, so ensure the color theme is not set to t0. Alternatively, a defective media LED strip or main control board could be the cause. In these cases, consider replacing the media LED strip or the main control board.
What to do if Dimplex Indoor Fireplace firebox does not turn on?
If your Dimplex Indoor Fireplace firebox isn't turning on using the manual controls, first ensure that the unit is not plugged into a power bar, surge protector, or extension cord. Also, check the fuse/breaker panel to ensure there is incoming power from the electrical wall socket. If those aren't the cause, the problem may be improper operation, so refer to the operation section. Other potential causes include a defective main control board, touchpad, or power supply, which would require replacement.
Why is the flame frozen on my Dimplex Indoor Fireplace?
If the flame is frozen on your Dimplex Indoor Fireplace, it could be due to a defective flicker motor, which would need replacing. Alternatively, the main control board might be defective and also need replacing.
How to fix light leaking around log set on Dimplex XHD26L?
If light is leaking out around the log set of your Dimplex Indoor Fireplace, it's likely that the log set is not positioned properly. Refer to the instructions for replacing the log set and make sure the log set is connected to the base panel.
Why does the circuit breaker trip when I turn on my Dimplex XHD26L Indoor Fireplace?
If the circuit breaker trips or a fuse blows when you turn on your Dimplex Indoor Fireplace, it could be due to two main reasons. First, the current rating of the circuit breaker or fuse might be exceeded by the combined power draw of the fireplace and other appliances on the same circuit. Try plugging the unit into another outlet or installing it on a dedicated 15 amp circuit. Second, there might be a short in the unit's wiring, in which case you should trace the wiring in the unit.
Why is the left half of the flame not visible on my Dimplex XHD26L?
If the left half of the flame is not visible on your Dimplex Indoor Fireplace, it could be due to a broken flicker rod, which would need to be replaced.
Outlines fundamental safety measures to reduce risks of fire, shock, and injury during appliance use.
Details specific safety warnings for unit handling, battery use, and temperature hazards.
Advises on proper placement, clearance, and opening requirements for installation.
Details steps for mounting the fireplace, including media dispersal and mantel installation.
Introduces the touch panel and infrared remote control for operating the fireplace.
General| Brand | Dimplex |
|---|---|
| Model | XHD26L |
| Category | Indoor Fireplace |
| Language | English |
To Next Page
