Dirt Devil Evo - User Manual

Questions and Answers

M
Matthew WhitakerAug 12, 2025
What to do if the central LED is emitting a red light on my Dirt Devil Vacuum Cleaner?
- K
  kingcodyAug 12, 2025
  If the central LED on your Dirt Devil Vacuum Cleaner emits a red light, it indicates a fault. This may happen because the appliance is stuck or cannot return to its starting position. To resolve this, turn off the appliance, place it on an open surface, and turn it back on. Another reason could be that the control cube was moved during operation or its signal was interrupted. In this case, switch off the appliance, reposition the control cube, and then turn it back on.
J
Jonathan KnappAug 15, 2025
Why is my Dirt Devil Vacuum Cleaner not charging?
- K
  Kendra Wood MDAug 15, 2025
  If your Dirt Devil Vacuum Cleaner isn't charging, first ensure that the appliance is switched off. If it is on, switch it off. Also, verify that the mains adapter is correctly plugged into both the appliance and the power socket.
H
haileyyoungAug 20, 2025
Why does the control cube switch off before the Dirt Devil Evo Vacuum Cleaner has completely cleaned?
- D
  Dylan MiddletonAug 20, 2025
  If your Dirt Devil Vacuum Cleaner control cube switches off before cleaning is complete, it could be due to two reasons. First, the vacuum might be out of range. To fix this, switch off the appliance, move it closer to the control cube within the room, and switch it back on. Second, interference with the control cube's signal might be the cause. Make sure the control cube isn't near TVs, telephones, or fluorescent tubes.
C
Christine Williams MDAug 23, 2025
Why is the LED on the control cube emitting a red light on my Dirt Devil Evo?
- R
  robert38Aug 23, 2025
  If the LED on the control cube of your Dirt Devil Vacuum Cleaner emits a red light or doesn't switch on, it means the batteries in the control cube are empty. Replace them to solve the problem.
S
Stacy PenningtonAug 27, 2025
What to do if my Dirt Devil Evo Vacuum Cleaner only cleans parts of the room?
- S
  Steven ReillyAug 27, 2025
  If your Dirt Devil Vacuum Cleaner is switched on, but none of the status LEDs are on, or if it only cleans parts of the room, the control cube might not be switched on. If you want to use the control cube for efficient cleaning, switch it on. Also, check the batteries in the control cube; a red light indicates they are dead and need replacement. Finally, ensure the control cube is positioned correctly: place it on a high piece of furniture where it can send a signal to the ceiling without obstruction, with its blue LED pointing into the room and away from the nearest walls.
L
Leslie JordanAug 31, 2025
What to do if my Dirt Devil Evo Vacuum Cleaner can be switched on, but won’t start?
- C
  Christopher BarkerAug 31, 2025
  If your Dirt Devil Vacuum Cleaner won't start after being switched on, it could be due to a couple of reasons. First, the on/off switch might be flashing red or showing a continuous red light, indicating that the batteries are low and need to be charged. Second, you might not have selected a cleaning mode after switching on the appliance. Make sure to select a cleaning mode immediately after turning on the vacuum.
A
Aaron GravesSep 3, 2025
Why are all the lights on at the same time on my Dirt Devil Evo Vacuum Cleaner?
- P
  Pamela JohnsonSep 3, 2025
  If all lights (illuminated buttons and LEDs) are on simultaneously on your Dirt Devil Vacuum Cleaner, it means you've likely tried charging the appliance with a non-supplied mains adapter. To fix this, only use the mains adapter that came with the sweeping robot to charge it.
S
Scott IbarraSep 7, 2025
Why does my Dirt Devil Vacuum Cleaner not move straight in dusting mode?
- J
  Jeff HahnSep 7, 2025
  If your Dirt Devil Vacuum Cleaner does not move in a straight line in ‘dusting’ mode, even in an open space, it may be due to selecting the wrong mode. Try switching the appliance off and back on, then select the ‘dusting’ mode again. Another possible cause is that the floor cloth isn't taut enough or has creases. In this case, switch off the appliance and reattach the floor cloth, ensuring it lies flat on the floor cleaning panel and that its holes are not covered.