18
1800-060 Issued 7-19
Version A
Low Voltage/
Communication
Wire Conduit
High Voltage
Power Wire
(115 V) Conduit
Electrical field from high voltage wires.
6” minimum
Underground Cutaway
SECTION 2 - WIRING
Be sure that you use proper wire that has an insulation
rated for an underground environment. All wires
should be placed in conduits. Proper pre-planning can
greatly ease the installation and wiring of this system.
Always check with the local building code to determine
the type of wire required in your municipality.
DO NOT run high voltage (115 V) power lines and low voltage/communication lines in the same conduit. These should be in
separate conduits at least six (6) inches apart. Be sure that all phone line wiring is twisted and completely isolated from ground.
Prior to installing wiring to the telephone entry system, we suggest that you become familiar with the instructions, illustrations,
and wiring guidelines in this manual. This will help insure that you installation is performed in an efficient and professional
manner.
The wiring of the telephone entry panel is an extremely important and integral part of the overall access control system. Use
proper wire for the communication line, power wires, and be sure that the system is properly grounded. Check all local building
ordinances and building codes prior to installing this system. Be sure your installation is in compliance with local codes.
Telcom Access Standards. It is not permissible for customers to use the telcom network lead-in cable to provide the intercom
function between the gate and the house. New Zealand Customers: All door and gate entry systems wiring must comply with
PTC106: March 2008, Section 9.
WARNING If this telephone entry system is used to control a vehicular gate with an automatic gate operator, the telephone
entry system must be mounted a minimum of six (6) feet away from the gate and gate operator, or in such a way that the
user cannot come into contact with the gate or gate operator when using this entry system. If this unit has been installed
closer to the automated vehicular gate, do not proceed with any wiring until the unit has been moved and re-installed so
that it is in compliance with these instructions.
This telephone entry system contains a number of static sensitive components that can be damaged or destroyed by static
discharges during installation or use. Discharge any static prior to removing the circuit board from the enclosure by touching
a proper ground device.
Use only the supplied transformer (or UL listed equivalent) to power the telephone entry system. DO NOT power any other
devices (electric strikes, magnetic locks, lights etc.) from this power transformer.
Note: Transformer is not supplied on units sold outside the United States. An Inherently Protected Transformer must be used to
power this device. Only use transformer that is listed by a recognized testing laboratory to power the telephone entry system.
“Optional” 12 volt .8 amp hour gel-cell battery (DoorKing P/N 1801-008) can be installed to provide stand-by power in the
event of a power outage.
2.1 Wiring Guidelines
2.1.1 Power
2.1.2 Wire Runs
Up to 100 feet, use 18 AWG, 600 volt insulated wire.
Up to 200 feet, use 16 AWG, 600 volt insulated wire.
The importance of proper AWG power wiring cannot be over stressed!
Wire polarity does not matter
Power wires are susceptible to noise and hum pickup; therefore
it is preferable that you keep power wire runs as short as possible.
16.5 VAC, 20 VA
Operating Instructions
1. Locate Code Number On Directory
2. Press Code Number. If Line Is Busy, Press Any Button
to Hang-Up. Try Again.
3. Enter On “OPEN” Display or Tone.
NAME
Adams J
Akins M
Annese J
Anderson H
Applegate B
Austin D
Balsbaugh B
Bass J
Bejar I
Berlin J
Bernard E
Billings L
Broker T
Brose S
Brown J
Brown K
Bryant W
Byron R
Byan G
009
115
352
551
656
078
221
321
249
476
003
112
292
822
491
324
231
332
117
CODE NAME
Byers M
Cardillo P
Carney P
Collins G
Colyer R
Cordula D
Court E
Crains G
Dalton B
Daniels R
Dawls J
DeLahae M
Dill P
Dillon M
Dixon D
Dominick P
Donick P
Donner K
Donter F
807
503
501
404
461
249
772
633
481
104
322
068
888
518
358
467
765
954
992
CODE
NAME
Dorland T
Downward L
Dubreuil M
Dukes D
Enghard L
Ellis W
Farago F
Farrow M
Fernandez S
Garfield S
Garreau J
Gentry M
Gonzalez H
Haberfeld A
Hammer V
Hendrix K
Hird A
Hitch J
Hitch F
Hodges A
Hoover H
Jensen D
Johnson M
Johnson T
Jones A
Jones G
290
152
028
072
828
342
733
441
612
914
542
120
732
18
6
232
333
835
302
064
005
490
341
879
557
032
419
CODE NAME
Jordan M
Jorden L
Jorgensen B
Klein D
Knoblich B
Lamb B
Land D
Landers S
Langstrom B
Levine D
Lewis B
Lucidi B
Mancini G
Mastin D
Maston F
Mozina J
Mucera J
Mulin B
Nabor K
Nabur J
Neumann J
Nixon R
Patterson F
Perez F
Petrolli A
Ray J
023
562
647
736
408
803
026
996
338
476
101
069
247
122
040
640
447
006
745
546
501
330
211
543
987
352
CODE NAME
Reese D
Reiger B
Remington S
Ressegieu R
Rollins A
Schuster S
Seeley J
Selleck H
Shaer R
Shank D
Simons L
Smith J
Somach H
Steele F
Stollach H
Synfol A
Tomlinson L
Tompson A
Tompson S
Tyler Q
Washington G
Washington K
Went L
Whiting M
Winston F
Wyatt J
081
148
887
063
883
551
731
435
055
082
650
791
021
076
100
334
213
229
007
134
609
389
679
211
670
441
CODE
7
8
9
4
5
6
1
2
3
0
PERMANENT WIRING MUST BE EMPLOYED AS REQUIRED BY LOCAL
ELECTRICAL CODES. ALWAYS ADHERE TO THE LOCAL AND NATIONAL
ELECTRICAL CODE SPECIFICATIONS WHEN WIRING THE TELEPHONE ENTRY
SYSTEM/ACCESS CONTROLLER AND OTHER ACCESS CONTROL DEVICES.
Do Not Connect To A
Receptacle Controlled
By A Switch.
To Next Page
Loading...
