DSC Power632

Programming Worksheets
41
[370] Communication Variables
Default Section Page #
003 I_______I_______I_______I Swinger Shutdown (Alarms and Rest) (001-014 Transmissions, 000=disabled) 5.20 25
003
I_______I_______I_______I Swinger Shutdown (Tampers and Rest)(001-014 Transmissions, 000=disabled) 5.20 25
003 I_______I_______I_______I Swinger Shutdown (Maint and Rest) (001-014 Transmissions, 000=disabled) 5.20 25
000
I_______I_______I_______I Transmission Delay (001-255 seconds) 5.16 24
030
I_______I_______I_______I AC Failure Communication Delay (001-255 minutes) 5.9 18
003 I_______I_______I_______I TLM Trouble Delay (No. of checks required - valid entries 003 - 255) 5.13 23
030
I_______I_______I_______I Test Transmission Cycle (land line) (001-255 minutes/days)† 5.15 23
030
I_______I_______I_______I Test Transmission Cycle (GSM) (001-255 days) 5.15 23
007 I_______I_______I_______I Zone Low Battery Transmission Delay (000-255 days) 5.9 18
030
I_______I_______I_______I Delinquency Transmission Cycle (000-255 days/hours) 5.9 18
†Depends on programming in section [702], option [3].
NOTE: To disable the AC failure communications delay, program [000].
[371] Test Transmission Time of Day
(Section 5.15 “Test Transmission” on page 23)
NOTE: If the land line test transmission cycle is programmed in minutes (section [702], option [3]), this section will not affect the land
line test transmission cycle.
Default
9999
I_______I_______I_______I_______I (Valid entries are 0000-2359, 9999 to disable)
[380] First Communicator Option Code
Default Option ON OFF Section Page #
ON
I_______I 1 Communications Enabled Communications Disabled 5.6 17
OFF
I_______I 2 Restorals on Bell Time-out Restorals Follow Zones 5.9 18
OFF
I_______I 3 Pulse Dialing DTMF Dialing 5.6 17
OFF
I_______I 4 Switch to Pulse Dialing on 5th Attempt DTMF Dial For All Attempts 5.6 17
OFF
I_______I 5 3rd Telephone Number enabled 3rd Telephone Number disabled 5.8 18
OFF
I_______I 6 Alternate Dial (1st and 3rd) Call 1st Number, Backup to 3rd 5.8 18
OFF
I_______I 7 Call GSM as well as Land Line GSM is Backup of Land Line(s) 5.27 26
OFF
I_______I 8 Delinquency Follows Zone Activity (Hours) Delinquency Follows Arming (Days) 5.9 18
[381] Second Communicator Option Code
Default Option ON OFF Section Page #
OFF
I_______I 1 Open After Alarm Kypd Ringback enabled Open After Alrm Kypd Ringback disabled 5.18 24
OFF
I_______I 2 Open After Alarm Bell Ringback enabled Open After Alrm Bell Ringback disabled 5.18 24
OFF
I_______I 3 SIA Sends Programmed Rep. Codes SIA Sends Automatic Rep. Codes 5.10 19
OFF
I_______I 4 Closing Confirmation Enabled Closing Confirmation Disabled 5.18 24
OFF
I_______I 5-6 For future use —
ON I_______I 7 Contact ID Uses Programmed Rep. Codes Contact ID Uses Automatic Rep. Codes 5.10 19
OFF I_______I 8 For future use —
[390] GSM Preamble (First Telephone Number)
(Section 5.27 “GSM1000 Cellular Communicator” on page 26)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[391] GSM Preamble (Second Telephone Number)
(Section 5.27 “GSM1000 Cellular Communicator” on page 26)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[392] GSM Preamble (Third Telephone Number)
(Section 5.27 “GSM1000 Cellular Communicator” on page 26)
Default: FFFF I_______I_______I_______I_______I (Program all unused digits with Hex F)
[393] GSM Special Function Preamble (All Telephone Numbers)
(Section 5.27 “GSM1000 Cellular Communicator” on page
26)
Default: FFFFFF I_______I_______I_______I_______I_______I_______I (Program all unused digits with Hex F)
•Enter [*][2][*] (Hex B) to dial [*] • Enter [*][3][*] (Hex C) to dial [#]