DURAG D-R 290 User Manual

List of figures
8
D-R 290
Fig. 7.3 Setting DURAG − Modbus address..............................................................................................
121
Fig. 7.4 Setting DURAG – Modbus communication settings ....................................................................
123
Fig. 7.5 Setting variables for the measurement channels.........................................................................
125
Fig. 7.6 Common parameters D‑R 290 Variables setting I........................................................................
131
Fig. 7.7 Diagram: Measured value correction by polynomial (example)...................................................
132
Fig. 7.8 Common parameters D‑R 290 Variables setting II.......................................................................
133
Fig. 7.9 Setting the analogue output.........................................................................................................
134
Fig. 7.10 Setting relay setup........................................................................................................................
136
Fig. 7.11 Setting the relay settings..............................................................................................................
138
Fig. 7.12 Setting the maintenance settings.................................................................................................
139
Fig. 7.13 Device configuration.....................................................................................................................
141
Fig. 7.14 Measured values..........................................................................................................................
142
Fig. 7.15 Calibration....................................................................................................................................
143
Fig. 7.16 Device status
................................................................................................................................
144
Fig. 7.17 Pin assignment or the purge air monitoring plug..........................................................................
145
Fig. 7.18 Connection plugs and sockets on the underside of the housing..................................................
145
Fig. 7.19 Quick Info explanation of the shutter status.................................................................................
145
Fig. 7.20 Dust-free measurement................................................................................................................
147
Fig. 7.21 Diaphragm....................................................................................................................................
148
Fig. 7.22 Measurement tube for a smoke-free measurement path.............................................................
148
Fig. 7.23 Temperaturetransmitter................................................................................................................
149
Fig. 7.24 Pin assignmentconnection , temperature transmitter...................................................................
150
Fig. 7.25 Electrical connection of a 2-wire transducer (without its own power supply)...............................
150
Fig. 7.26 Electrical connection of a 4-wire-transducer (with its own power supply)....................................
150
Fig. 8.1 Purge air filter...............................................................................................................................
156
Fig. 8.2 Optical surfaces
............................................................................................................................
157
Fig. 8.3 EPA-Test filter
..............................................................................................................................
158
Fig. 8.4 Insert the test filter into the device
................................................................................................
159
Fig. 8.5 Example of a linearity test without scaling....................................................................................
160
Fig. 8.6 Example of a linearity test with scaling.........................................................................................
161
Fig. 8.7 Turntable plate.............................................................................................................................
162
Fig. 8.8 LED 5
...........................................................................................................................................
164
Fig. 8.9 Attachment screws for thehousing cover.....................................................................................
164
Fig. 8.10 Undo.............................................................................................................................................
165
Fig. 8.11 Changing the battery....................................................................................................................
165
Fig. 8.12 Tightening.....................................................................................................................................
166
Fig. 9.1 Measurement point questionnaire 1.............................................................................................
177
Fig. 9.2 Measurement point questionnaire 2.............................................................................................
178
Fig. 9.3 Dimensional diagram of the measuring head/reflector.................................................................
182
Fig. 9.4 Installation example on a horizontal duct.....................................................................................
183
Fig. 9.5 Dimensional diagram of the measuring head/reflector with fail-safe shutter................................
184
Fig. 9.6 Installation example on a horizontal duct.....................................................................................
185
Fig. 9.7 Dimensional diagram D−R 290 standard welded-in pipe with adjustment flange (↘= red dot)....
185
Fig. 9.8 Housing D-SK AE dimensional diagram, space required.............................................................
186
Fig. 9.9 Dimensional diagram housing D-SK 290 MA *D1 diameter 100 mm ..........................................
187
Fig. 9.10 Dimensional diagram housing D-SK 280 MA *D1 diameter 150 mm ..........................................
187
Fig. 9.11 Dimensional diagram D-TB 100 supply unit.................................................................................
188
Fig. 9.12 Dimensional diagram purge air unit *D1 diameter 100 mm (*D1 see Welded-in pipe lengths )...
189
Fig. 9.13 Dimensional diagram purge air unit *D1 diameter 150 mm (*D1 see Welded-in pipe lengths )...
190
Fig. 9.14 Dimensional diagram weather protection cover, measuring head D1 (pitch circle diameter
100)*............................................................................................................................................. 191

DURAG D-R 290 Specifications

General

Brand	DURAG
Model	D-R 290
Category	Monitor
Language	English