Why is my Dynex LCD TV remote control not working?
If the remote control for your Dynex LCD TV isn't working, check these: - Make sure the power cord is correctly connected to your TV and a power outlet. - Ensure there are no obstructions between the remote and the TV's sensor. - Point the remote directly at the sensor on the TV. - Verify the batteries are correctly installed. - Replace dead batteries with new ones.
What to do if my Dynex LCD TV only displays snow (noise) on the screen?
If your Dynex LCD TV only displays snow (noise) on the screen: - Try another channel. - Ensure the antenna or cable TV is connected correctly and securely. - If you're using an antenna, the digital channel signal may be low. If the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier.
How to fix audio noise on Dynex LCD TV?
If you are experiencing audio noise with your Dynex LCD TV, other devices (for example, surround sound receiver, external speakers, fans, or hair dryers) may be interfering with your TV. Try turning off one device at a time to determine which device is causing interference. Once you have determined which device is causing interference, move it further from the TV to eliminate the interference.
How to fix no color or dark picture on Dynex LCD TV?
If your Dynex LCD TV has no color, a dark picture, or incorrect color: - Try another channel. - Adjust the color saturation. - Make sure the video cables are connected correctly and securely to the back of your TV. - Ensure the antenna or cable TV is connected correctly and securely. - If you are using an antenna, the digital channel signal may be low. If the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier.
How to fix poor picture quality on Dynex LCD TV?
To improve poor picture quality on your Dynex LCD TV: - Make sure the room is not too bright, as light reflecting off the screen can make the picture difficult to see. - If an S-VHS camera or camcorder is connected while another device is on, the picture may be poor. Try turning off one or more devices.
What to do if my Dynex LCD TV has dark, poor, or no picture but sound is good?
If your Dynex LCD TV has a dark, poor, or no picture (but sound is good), try these: - Try another channel. - Make sure that the antenna or cable TV is connected correctly and securely. - Ensure that Audio Only option is set to Off. - Adjust the brightness. - Select the correct picture mode. - If you are using an antenna, the digital channel signal may be low. If the signal strength is low, adjust the antenna or use a highly directional outdoor antenna or set-top antenna with a built-in amplifier. - Make sure that the video cables are connected securely to the back of your TV. - The video cable(s) you are using may be bad. Try a new set.
What to do if my Dynex DX-24L230A12 LCD TV displays a 'no signal' error message?
If your Dynex LCD TV displays a 'no signal' error message: - Press the INPUT button and select the correct input for your device or service. - If using a cable or satellite box, use its remote to change channels.
What to do if my Dynex LCD TV has good picture, but no sound?
If your Dynex LCD TV has a good picture but no sound, consider the following: - Increase the volume. - Ensure the sound is not muted. - Select the correct audio mode. - Check that the audio cables are correctly and securely connected to the back of your TV. - Ensure the antenna or cable TV is connected correctly and securely. - If you are using an antenna, the digital channel signal may be low. - The audio cable(s) you are using may be bad; try a new set.
Why is there no picture and sound on my Dynex DX-24L230A12?
If your Dynex LCD TV has no picture and no sound, try the following: - Press the power button on the TV or the remote control. - Ensure the power cord is plugged in. - Check that the video cables are securely connected to the back of your TV. - Select the correct video input source. - Adjust the contrast and brightness. - Try another channel to rule out station problems. - Verify that the incoming signal is compatible. - Ensure the antenna or cable TV is connected correctly and securely. - Check the closed caption settings, as some TEXT modes can block the screen.
What to do if my Dynex DX-24L230A12 LCD TV has no power?
If your Dynex LCD TV has no power: - Make sure that the power cord is correctly connected to your TV and a power outlet. - Unplug the power cord, wait 60 seconds, then plug the cord back in and turn on your TV. - Other devices may be interfering with your TV. Try turning off one device at a time to determine which device is causing interference. Once you have determined which device is causing interference, move it further from the TV to eliminate the interference.
General| Screen Size | 24 inches |
|---|---|
| Display Type | LCD |
| Resolution | 1366 x 768 |
| Aspect Ratio | 16:9 |
| Brightness | 250 cd/m² |
| Contrast Ratio | 1000:1 |
| Response Time | 5 ms |
| HDMI Ports | 2 |
| USB Ports | 1 |
| Viewing Angle | 170° (H) / 160° (V) |
| Speakers | 2 x 3W |
| Inputs | HDMI, VGA, Component, Composite, RF |
| Dimensions (W x H x D) | 7.1 inches (180 mm) |
To Next Page
