- 28 -
- 29 -
Fu nct ion C ode T abl e
EC 600 0
Fu nct ion C ode T abl e
EC 600 0
P5-33
P5-34
A01 output gain
A01 output offset
coefficient
0521H
0522H
25.0 200.0%～
-10.0 10.0%～
100.0%
0.0%
P5-35
P5-36
P5-37
0523H
0524H
0525H
100.0%
0.0%
0.20KHz
25.0 200.0%～
-10.0 10.0%～
0.00 50.00KHz～
A02 output gain
A02 output offset
coefficient
HY pulse output
lower limit
P5-38 0526H
50.00KHz 0.00 50.00KHz～
HY pulse output
upper limit
P6 S t ar t/S top C on tro l par am e te rs
Parameter Name
Setting Range
Start mode
BIT0：Start mode
0: Direct start
1: First braking and then start by startup
frequency
2: Rotational speed tracking
RESTART
0.00 P6-04～
Minimum output
frequency
Function
Code
P6-00
P6-01
P6-02
0 100%～
Startup
pre-excited current
Startup
pre-excited time
Startup frequency
Startup frequency
holding time
Startup DC
braking current
Startup DC
braking time
0.00 60.00s～
0.00 60.00Hz～
0.00 50.00s～
0 150%～
0.0 300.0s～
P6-03
P6-04
P6-05
P6-06
P6-07
Address
0600H
0601H
0602H
0603H
0604H
0605H
0606H
0607H
Model
dependent
0.50Hz
Default
0
0.50Hz
30%
0.0s
0%
0.0s
Stop DC
braking current
Waiting time of
stop DC braking
Stop DC braking
holding time
Acceleration mode
selection
Zero speed
holding current
Initial frequency
of stop DC braking
0 150%～
0.00 60.00s～
0.00 600.0s～
BIT0：Acceleration/Deceleration time
frequency base
0：Base:50.00Hz 1:Maximum frequency
BIT1：S-curve selection
0: Straight line 1: Curve
0 150%～
0.00 50.00Hz～
P6-09
P6-10
P6-11
P6-13
P6-12
P6-08
0609H
060AH
060BH
060DH
060CH
0608H
0.00Hz
0%
0.0s
0.0s
00
0%
Start of S-curve
acceleration time
End of S-curve
acceleration time
Start of S-curve
deceleration time
End of S-curve
deceleration time
Rotational speed
tracking mode
0.01 20.00s～
0: From frequency at stop 1: From zero speed
2: From maximum frequency
P6-14
P6-15
P6-16
P6-17
P6-18
060EH
060FH
0610H
0611H
0612H
0.50
0.50
0.50
0.50
0
P6-19
Waiting time of
rotational speed
tracking
0.0 600.0s～
0613H
1.0s
P6-20
Tracking speed
of rotational
speed
0 100～ 0614H
20
P7 S ys tem c onf igu ra tio n par am ete rs
Function
Code
P7-00
Parameter Name
Parameter and key
lock selection
Address
0700H
Setting Range
BIT0:
0: Not locked
1: Function parameter locking
2: Function parameters and key locking (except
RUN/STOP/JOG)
3: Function parameters and keys are fully
locked
Default
0
P7-01
User password
0701H
0 65535～
0
P7-02
STOP key
function
0702H
BIT0: 0: Invalid for terminal command
1: Valid for terminal command
BIT1: 0: Invalid for communication command
1: Valid for communication command
BIT2: 0: Invalid for expansion card command
1: Valid for expansion card command
000
P6-21
Torque tracking
closed loop
current KP
0 1000～ 0615H
50
P6-22
0 1000～
0616H
50
P6-23
30% 200%～ 0617H
100%
P6-24
Torque tracking
current lower
limit
10 100%～ 0618H
30%
Torque tracking
closed loop
current KI
Torque tracking
current
P6-25
0.5 30s～ 0619H
1.1
P6-26
Torque tracking
demagnetization
time
0.00 5.00s～ 061AH
1.00s
Torque tracking
rise time
To Next Page
Loading...
