- 30 -
- 31 -
Fu nct ion C ode T abl e
EC 600 0
Fu nct ion C ode T abl e
EC 600 0
Display speed
factor
P7-03
P7-04
P7-05
P7-06
P7-07
P7-08
MF.K Key
function
selection
Copy of function
parameters
First line
run display
First line
stop display
Second line
run display
0703H
0704H
0705H
0706H
0707H
0708H
BIT0: Panel digital potentiometer setting
selection
0: Invalid 1: Main frequency
2: Auxiliary frequency 3: Upper frequency
4: V/F separated voltage 5: PID setting
6: PID feedback 7: Torque setting
BIT1:
0: Directly valid after the knob is modified
1: Press the Enter key to be valid after the
knob is modified
0: No operation
1: Proofread data, parameter copy
2: Write keyboard data to AC drive
0.001 50.000～
BIT0: The first group displays
BIT1: The second group displays
BIT2: The third group displays
BIT3: The fourth group displays
0: Given frequency 1: Output frequency
2: Output current 3: Output voltage
4: Input voltage 5: Mechanical speed
6: Bus voltage 7: Output power
8: Given torque 9: Output torque
A: AI1 input value B: AI2 input value
C: HS input value D: Power factor
E: PID setting F: Counter value
01
1.000
6321
Ca40
0792
0
0709HP7-09
Second line
stop display
OCA4
070AH
0～8
P7-10
Multi-function
expansion card
selection
0
BIT0: LCD operation panel display language
Set LCD operation panel display language,
only valid when using LCD operation panel.
070CH
070DH
070EH
070FH
0 65535～
0.0 6553.5～
0 65535～
0.0 6553.5～
P7-12
P7-13
P7-14
P7-15
Accumulated
power-on days
Accumulated
power-on hours
Accumulated
running days
Accumulated
running hours
Read-only
Read-only
Read-only
Read-only
070BH
0: Chinese
1: English
BIT1: Output frequency display selection
0: Target frequency displays the target
frequency of the current control motor.
1: Synchronous frequency displays the output
frequency after converting operation.
BIT2: Reserved
BIT3: LCD contrast adjustment
0-f: The larger the contrast value
P7-11
operation
panel display
item selection
8001
0710H
0711H
0～65535 million kWh
0～65535kWh
P7-16
P7-17
Accumulative power
consumption
(10000 kWh)
Accumulative
power
consumption
Read-only
Read-only
BIT0: 0: Stop 1: Run
BIT1: 0: Forward RUN 1: Reverse RUN
BIT2: Reserved BIT3: Reserved
AC drive status
before power off
P7-18 0712H
0000
0.00Hz to maximum frequency
5.00Hz
5.00Hz
10.0s
Forward JOG
running
frequency(FJOG)
Reverse JOG
running
frequency(RJOG)
JOG acceleration
time
P8-00
P8-01
P8-02
0800H
0801H
0802H
P8 A u xi lia ry Fu nc tio ns
Function
Code
Parameter Name
Setting Range
Default
Address
0.00Hz to maximum frequency
10.0s
JOG deceleration
time
P8-03 0803H
10.0s
Acceleration
time 2
P8-04 0804H
10.0s
Deceleration
time 2
P8-05 0805H
10.0s
Acceleration
time 3
P8-06 0806H
10.0sP8-07 0807H
0.1～6500.0s
10.0s
Acceleration
time 4
P8-08 0808H
10.0s
Deceleration
time 4
P8-09 0809H
10.0s
Emergency stop
deceleration
time
P8-10
080AH
0.0～150.00s 0.00s
Forward/Reverse
rotation dead-
zone time
P8-11
080BH
Jump frequency 1
P8-12
0.00Hz
080CH
Jump frequency 2
P8-13
0.00Hz
080DH
0.00Hz to maximum frequency
Jump frequency
amplitude
P8-14
0.00Hz
080DH
Deceleration
time 3
Frequency
detection value
(FDT1)
P8-15
30.00Hz
080FH
Detection range
of FDT1
P8-16
0.00Hz
0810H
To Next Page
Loading...
