What to do if Eagle 2000 B Gate Opener machine will not start job after reset?
If your Eagle Gate Opener won't start a job after a reset: * Check if Input 04 is not lit. The Photoelectric Eye is not sending a signal to PLC. * The Photoelectric Eye might not be reading the package. Ensure that both green and amber lights are illuminated with a load in place.
How to fix Eagle 2000 B scale that does not work?
If the scale on your Eagle Gate Opener isn't working: * Ensure the machine is level by placing it on a flat surface and using a level. * Verify that all leveling feet are properly placed by screwing them into the load cell.
Why Eagle 2000 B machine will not function?
Your Eagle Gate Opener might not function due to several reasons: * It might not be plugged into a 110VAC outlet. If so, plug it in. * The outlet itself might lack power or be faulty. Check the outlet. * The power cord could be damaged, requiring a replacement. * The internal circuit breaker might have tripped, in which case you should call tech support.
What to do if Eagle 2000 B carriage does not run?
If the carriage on your Eagle Gate Opener isn't running, consider these potential causes: 1. Ensure the machine is plugged into a functioning 110 Volt outlet. 2. Check the carriage speed knob; if it's at the minimum, adjust it to a higher setting using the speed potentiometer. 3. Inspect the chain for breaks or disconnections; replace or reinstall it, removing any obstructions. 4. If the carriage sliding block is jammed, loosen the slider blocks to realign and lubricate with a dry lube.
What to do if Eagle Gate Opener machine has power but is paused?
If your Eagle Gate Opener has power but is stuck in 'Machine Pause', here's what to check: * If input signal 05 is lit on the PLC, inspect all E-stops and clear any debris under the carriage. * Ensure the E-stop on the main panel isn't pushed in. Check all E-stops and clear any debris under the carriage. * The carriage base safety switch might be pushed. Adjustment may be needed to carriage safety switch. * Confirm that the Film Feed Door is properly closed with a firm push, avoiding slamming or forcing it. * The drive display should show 'rdy'. If it doesn't, call tech support.
Why Eagle 2000 B machine will not stop at home?
If your Eagle Gate Opener isn't stopping at home, consider these potential causes: * Input signal 03 might not be lit on the PLC. This Input will only illuminate when the Limit Switch is on the cam location. * There might be a bad connection between the mass and turntable. Tighten or replace the connector, ensuring there are no pinched wires. * The Limit Switch might be bad or need adjustment. Replace the Limit Switch or adjust it so that it rides on the cam properly.
Why does my Eagle 2000 B screen display Chinese lettering?
If your Eagle Gate Opener screen is displaying Chinese lettering: * The DB9 connector may have come unplugged or is loose. Tighten the connector on the PLC and Screen / Be sure to check power connections as well. * The DB9 connector might be faulty. Replace the DB9 Connector / call tech support.
Crucial safety guidelines and warnings for machine operation and maintenance.
Technical specifications for the Eagle 2000 series stretch wrapper models.
Overview of the machine's design, capabilities, and suitable industries.
Guidelines on the correct and safe operator standing position during machine use.
Essential safety steps to perform before starting machine operation.
Diagram illustrating the main parts and structure of the stretch wrapper.
Procedures and safety advice for safely moving and transporting the machine.
Step-by-step guide for setting up and installing the stretch wrapper.
Recommended environmental conditions for optimal machine performance and safety.
Instructions on how to load stretch film into the machine carriage.
Fundamental steps for operating the stretch wrapper for packaging.
Guide to using and navigating the machine's LCD control screen.
Detailed explanation of menu navigation and screen functions for machine settings.
Procedures for setting and managing machine passwords for security.
Overview of the optional weight scale system and its functions.
List of error codes for the weight scale and their corresponding solutions.
Common problems, possible causes, and solutions for machine issues.
Instructions on how to adjust the carriage load safety switch.
Information regarding the turntable home switch and associated maintenance.
Procedures for adjusting the turntable and carriage mechanisms.
Exploded view and part list for the machine's base assembly.
Exploded view and part list for the idler wheel components.
Exploded view and part list for the machine's mast assembly.
Exploded view and part list for the film carriage assembly.
Exploded view and part list for the film roller components.
Exploded view and part list for the extended roller components.
Wiring diagrams for the machine's motor control system.
Diagrams detailing the Programmable Logic Controller (PLC) wiring.
Electrical schematic for the optional weight scale system.
Wiring diagrams for the machine's switches and relays.
General| Model | Eagle 2000 B |
|---|---|
| Category | Gate Opener |
| IP Rating | IP44 |
| Maximum Gate Weight | 400 kg |
| Maximum Gate Width | 6 m |
| Operating Temperature | -4°F to +158°F |
To Next Page
