Eagle 2000 BWS - User Manual

Questions and Answers

H
Heather ValdezAug 4, 2025
What to do if Eagle Gate Opener machine will not start job after reset?
- F
  Frederick GrahamAug 4, 2025
  If your Eagle Gate Opener won't start a job after a reset: * Check if Input 04 is not lit. The Photoelectric Eye is not sending a signal to PLC. * The Photoelectric Eye might not be reading the package. Ensure that both green and amber lights are illuminated with a load in place.
M
Megan ThomasAug 8, 2025
How to fix Eagle 2000 BWS Gate Opener scale that does not work?
- W
  Wesley AdamsAug 8, 2025
  If the scale on your Eagle Gate Opener isn't working: * Ensure the machine is level by placing it on a flat surface and using a level. * Verify that all leveling feet are properly placed by screwing them into the load cell.
S
schavezAug 13, 2025
Why Eagle 2000 BWS Gate Opener machine will not function?
- M
  mendezrachelAug 13, 2025
  Your Eagle Gate Opener might not function due to several reasons: * It might not be plugged into a 110VAC outlet. If so, plug it in. * The outlet itself might lack power or be faulty. Check the outlet. * The power cord could be damaged, requiring a replacement. * The internal circuit breaker might have tripped, in which case you should call tech support.
N
Nicholas ReillyAug 17, 2025
What to do if Eagle 2000 BWS carriage does not run?
- C
  Charles SmithAug 17, 2025
  If the carriage on your Eagle Gate Opener isn't running, consider these potential causes: 1. Ensure the machine is plugged into a functioning 110 Volt outlet. 2. Check the carriage speed knob; if it's at the minimum, adjust it to a higher setting using the speed potentiometer. 3. Inspect the chain for breaks or disconnections; replace or reinstall it, removing any obstructions. 4. If the carriage sliding block is jammed, loosen the slider blocks to realign and lubricate with a dry lube.
N
nathanrobinsonAug 22, 2025
What to do if Eagle 2000 BWS Gate Opener machine has power but is paused?
- T
  Tonya AndersonAug 22, 2025
  If your Eagle Gate Opener has power but is stuck in 'Machine Pause', here's what to check: * If input signal 05 is lit on the PLC, inspect all E-stops and clear any debris under the carriage. * Ensure the E-stop on the main panel isn't pushed in. Check all E-stops and clear any debris under the carriage. * The carriage base safety switch might be pushed. Adjustment may be needed to carriage safety switch. * Confirm that the Film Feed Door is properly closed with a firm push, avoiding slamming or forcing it. * The drive display should show 'rdy'. If it doesn't, call tech support.
S
Sarah GrossAug 26, 2025
Why Eagle 2000 BWS machine will not stop at home?
- K
  kmyersAug 27, 2025
  If your Eagle Gate Opener isn't stopping at home, consider these potential causes: * Input signal 03 might not be lit on the PLC. This Input will only illuminate when the Limit Switch is on the cam location. * There might be a bad connection between the mass and turntable. Tighten or replace the connector, ensuring there are no pinched wires. * The Limit Switch might be bad or need adjustment. Replace the Limit Switch or adjust it so that it rides on the cam properly.
Z
zcunninghamAug 30, 2025
Why does my Eagle 2000 BWS Gate Opener screen display Chinese lettering?
- S
  sgarciaAug 30, 2025
  If your Eagle Gate Opener screen is displaying Chinese lettering: * The DB9 connector may have come unplugged or is loose. Tighten the connector on the PLC and Screen / Be sure to check power connections as well. * The DB9 connector might be faulty. Replace the DB9 Connector / call tech support.