EINHELL TC-SM 2131 Dual User Manual

GB
- 38 -
•
The following can have an influence on dust
development:
- Worn, damaged or cracked saw blades
- Recommended capacity of the vacuum ext-
raction system: 20 m/s
- Proper guidance of the workpiece
•
Blades made of high-alloy high-speed steel
(HSS) must not be used.
•
Keep the push stick or handle for a push
block at the machine at all times, even when
you are not using them.
2. Maintenance and service
•
The following conditions can have an influ-
ence on noise impact on the operator:
- Type of saw blade (e.g. saw blades desig-
ned to reduce noise development)
- Material of the workpiece
- The force with which the workpiece is pu-
shed against the saw
•
Faults on the machine or its guards, safety
devices and blade must be reported to the
person in charge as soon as they are disco-
vered.
3. Safe operation
•
Select a suitable blade for the material you
wish to saw.
•
Never use the drag, crosscut and miter saw to
cut any materials other than those specified
by the manufacturer.
•
Use only the transport devices to move the
equipment. Never use the guards for handling
or moving the equipment.
•
Use the saw only if the guards are correctly
positioned and only if the saw is in perfect
condition and has been properly serviced.
•
When cutting miters, make sure that the
device for swiveling the arm is fastened se-
curely.
•
The floor around the machine must be level,
clean and free of loose particles, such as
chips and cutting residues.
•
Make sure the workplace and the room are
sufficiently illuminated.
•
The operator must receive proper training
in the use, adjustment and operation of the
machine.
•
Use only properly sharpened saw blades
•
Check that the speed indicated on the saw
blade is at least as high as the speed indica-
ted on the saw.
•
Be sure to use only spacers and spindle rings
which are specified by the manufacturer as
suitable for the intended purpose.
•
If the machine is equipped with a laser, this
laser may not be replaced by a different type
of laser. Repairs may only be carried out by
the manufacturer of the laser or one of his
authorized agents.
•
Do not remove any cutting residues or other
parts of workpieces from the cutting zone
while the machine is running and not before
the saw unit is at rest.
•
Make sure that the machine is always secu-
red on a workbench or a table. Use the holes
in the machine‘s base frame to secure the
machine. Bolt the base frame to a workbench
or a table.
•
Support long workpieces (e.g. with a roller
table) to prevent them sagging at the end of
a cut.
•
To make cuts correctly and safely:
- Always clamp the workpiece securely to the
saw table
- Each time before making a cut, make sure
that the machine stands securely
4. Additional safety instructions
•
Always pull the plug out of the power socket
before adjusting or servicing the machine.
•
Give these safety instructions to all persons
who work on the machine.
•
Do not use this saw to cut fire wood.
•
Caution! Hands and fingers may be injured on
the rotating saw blade.
•
Before you use the machine for the first time,
check that the voltage marked on the rating
plate is the same as your supply voltage.
•
If you need to use an extension cable, make
sure its conductor cross-section is big
enough for the saw‘s power consumption.
Minimum cross-section: 1.5 mm².
•
If you use a cable reel, the complete cable
must be pulled off the reel.
•
Do not carry the saw by its power cable.
•
Operators have to be at least 18 years of age.
Trainees of at least 16 years of age are allo-
wed to use the machine under supervision.
•
Keep children away from the machine when it
is connected to the power supply.
•
Check the power cable. Never use a faulty or
damaged power cable.
•
Keep your workplace clean of wood scrap
and any unnecessary objects.
•
Persons working on the machine should not
be distracted.
•
After you have switched off the motor, never
slow down the saw blade by applying pressu-
re to its side.
Anl_TC_SM_2131_Dual_SPK8.indb 38Anl_TC_SM_2131_Dual_SPK8.indb 38 10.07.2018 08:16:3910.07.2018 08:16:39

EINHELL TC-SM 2131 Dual Specifications

General

Idle speed (max)	5000 RPM
Sound power level	104 dB
Miter setting (left)	45 °
Sound pressure level	93 dB
Input power	1800 W
Power source	AC
Blade bore	30 mm
Blade diameter	210 mm

Weight and Dimensions

Depth	717 mm
Width	455 mm
Height	393 mm
Weight	11000 g