ELBE Radio-keypad programming
Installation
Before physically installing the unit in its mounting position it is good practice to perform a practical test to assess the functionality and
effec
tive range. Please bear in mind that range may be up to 25 or 30% less when battery power is low.
Positioning
Apart from the distance from the receiver, the units should not be positioned in the vicinity of or -
worse still - in contact with metal structures, which could otherwise exert a signal shielding effect. Thanks
to the enclosure protection rating of IP 54, the digital selectors can be installed outdoors if required.
A: Changing the combination associated with channel 1 ◄ - Example:
This function allows you to change the combination associated with channel 1 ◄
1. Press the "0" key and hold it down while pressing and releasing 0 ◄
2. Release the "0"key
3. Type in the current number (original factory is,11) combination and press 11◄
4. Type in the new combination (up to 8 digits) and press ◄ ( e x a m p l e ) 12345 ◄
5. Type in the new combination again 12345 ◄
6. To enter the codefor the START control,. With the gate closed locate the SET button and push the button once.
7. While DL3 is flashing, dial in the new combination generated at step 4&5, (12345) followed by the ◄symbol.
B: changing the combination associated with channel 2 ► - Example:
This function allows you to change the combination associated with channel 2 ►
1. Press the "0" key and hold it down while pressing and releasing 0 ►
2. Release the "0" key ►
3. Type in the current (original) combination and press 22 ►
4. Type in the new combination (up to 8 digits ) and press ► ( e x a m p l e ) 23456 ►
5. Type in the new combination again 23456 ►
6. To enter the codefor the PEDESTRIAN. With the gate closed press SET button twice; LED DL3 will start to flash quickly.
7. While DL3 is flashing, dial in the new combination generated at step 4&5, (23456) followed by the ►symbol.
7. While DL3 is flashing, dial in the new combination generated at step 4&5, (12345) followed by the ◄symbol.
7. While DL3 is flashing, dial in the new combination generated at step 4&5, (12345) followed by the ◄symbol.
: changing the combination associated with channel 2 ► - Example:
: changing the combination associated with channel 2 ► - Example:
This function allows you to change the combination associated with channel 2 ► This function allows you to change the combination associated with channel 2 ►
1. Press the "0" key and hold it down while pressing and releasing 0 ► 1. Press the "0" key and hold it down while pressing and releasing 0 ►
3. Type in the current number (original factory is,11) combination and press 11◄
3. Type in the current number (original factory is,11) combination and press 11◄
4. Type in the new combination (up to 8 digits) and press ◄ ( e x a m p l e ) 12345 ◄ 4. Type in the new combination (up to 8 digits) and press ◄ ( e x a m p l e ) 12345 ◄
5. Type in the new combination again 12345 ◄
for the START control,. With the gate closed locate the SET button and push the button once. for the START control,. With the gate closed locate the SET button and push the button once.
Before physically installing the unit in its mounting position it is good practice to perform a practical test to assess the fu
tive range. Please bear in mind that range may be up to 25 or 30% less when battery power is low.
tive range. Please bear in mind that range may be up to 25 or 30% less when battery power is low.
Apart from the distance from the receiver, the units should not be positioned in the vicinity of or - Apart from the distance from the receiver, the units should not be positioned in the vicinity of or -
worse still - in contact with metal structures, which could otherwise exert a signal shielding effect. Thanks worse still - in contact with metal structures, which could otherwise exert a signal shielding effect. Thanks
to the enclosure protection rating of IP 54, the digital selectors can be installed outdoors if required. to the enclosure protection rating of IP 54, the digital selectors can be installed outdoors if required.
This function allows you to change the combination associated with channel 1 ◄
This function allows you to change the combination associated with channel 1 ◄
Before physically installing the unit in its mounting position it is good practice to perform a practical test to assess the functionality and Before physically installing the unit in its mounting position it is good practice to perform a practical test to assess the fu
To Next Page
Loading...
