- 5 - UNAC Guide No. 2- July 2005
MD
Ann. 1
Type of risks
Evaluation criteria and solutions to be adopted
(Tick the box corresponding to the solution adopted)
1.3.7
1.3.8
1.4
Mechanical risks due to
movement of the leaf.
[7] Dragging of the
h
ands on the hinges side
edge (Figure 1, risk D).
[8] Dragging of the feet
on the lower edge
(Figure 1, risk E).
[9] Dragging of the
hands on the drive unit
(Figure 1, risk F).
[10] Dragging, hooking
and cutting due to the
shaping of the mobile
leaf (Figure 1, risk G).
Check that there is a clearance > 25 mm,
or:
attach guards that prevent fingers from being inserted (for example a
rubber strip).
The clearance between the gate and ground must prevent the risk of
dragging of the feet.
N.B. Should, due to the slope of the ground, the cle
arance vary, guards
should be attached (e.g. rubber strips).
If the distances between the drive unit and the leaf vary, check on the
pre
sence of a clearance >
25 mm, or attach guards (e.g. covers or strips in
rubber).
Eliminate or protect any sharp edges, handles, projecting parts etc. (for
example by means of covers or strips in rubber).
1.5.1
1.5.2
1.5.10
1.5.11
Electrical and electromagnetic
c
ompatibility risks
[11] Direct and indirect
contacts.
Dispersion of electrical
energy.
[12] Risks relating to
electromagnetic
compatibility.
Use CE-marked components and materials pursuant to the Low Voltage
Directive (73/23/EEC).
Carry out the electrical connections, connection to the mains, earth
connections and relevant checks, in accordance with current regulations and
as indicated in the installation manual of the drive unit.
N.B. If the electrical supply line is already set up (via both a socket and a
connector block), declarations of conformity to Italian law no. 46/90 are not
necessary.
Use CE-marked components pursuant to the EMC Directive (89/336/EEC).
Carry out the installation as indicated in the manual for installation of the drive
unit.
1.2
1.5.3
1.2.3
1.2.4
Safety and reliability of
drive unit and control and
safety devices.
[13] Safety conditions in
t
he event of
malfunctioning and
power failure.
[14] Energy types other
than electrical energy
[15] Actuation and
disabling of the drive
unit.
[16] Power supply
switch.
Use drive units which comply with the standard EN 12453 and safety
devices which comply with the standard EN 12978.
If hydraulic drive units are used, they must comply with the standard EN
982; or
if pneumatic drive units are used, they must comply with the standard EN
983.
Check that, after a fault or power failure, the drive unit restarts safely
without creating hazardous situations.
Install an omnipolar switch for electrical insulation of the door/gate, in
accordance with current laws. This switch must be positioned and protected
against accidental or unauthorised actuation.
[13] Safety conditions in
[14] Energy types other [14] Energy types other
than electrical energy than electrical energy
Carry out the electrical connectio
connections and relevant checks, in accordance with current regulations and
connections and relevant checks, in accordance with current regulations and
as indicated in the installation manual of the drive unit. as indicated in the installation manual of the drive unit.
N.B. If the electrical supply line is already set up (via both a socket and a N.B. If the electrical supply line is already set up (via both a socket and a
connector block), declarations of conforconnector block), declarations of confor
Use CE-marked components pursuant Use CE-marked components pursuant
Carry out the installation as indicated in the manual for installation of the drive Carry out the installation as indicated in the manual for installation of the drive
Safety and reliability of Safety and reliability of
drive unit and control and drive unit and control and
safety devices. safety devices.
[13] Safety conditions in [13] Safety conditions in
the event of the event of
Eliminate or protect any sharp edges
, handles, projecting parts etc. (for
example by means of covers or strips in rubber).
example by means of covers or strips in rubber).
Use CE-marked components and materials pursuant to the Low Voltage
Use CE-marked components and materials pursuant to the Low Voltage
Carry out the electrical connectio Carry out the electrical connectio
connections and relevant checks, in accordance with current regulations and
attach guards that prevent fingers from being inserted (for example a
The clearance between the gate and ground must prevent the risk of The clearance between the gate and ground must prevent the risk of
ground, the clearance vary, guards ground, the clearance vary, guards
If the distances between the drive unit and the leaf vary, check on the If the distances between the drive unit and the leaf vary, check on the
25 mm, or attach guards (e.g. covers or strips in
25 mm, or attach guards (e.g. covers or strips in
, handles, projecting parts etc. (for
, handles, projecting parts etc. (for
To Next Page
Loading...
