Elektro-Automatik PS 9000 T Series User Manual

Page 3
EA Elektro-Automatik GmbH
Helmholtzstr. 31-33 • 41747 Viersen
Germany
Fon: +49 2162 / 3785-0
Fax: +49 2162 / 16230
www.elektroautomatik.de
ea1974@elektroautomatik.de
PS 9000 T Series
TABLE OF CONTENTS
1
GENERAL
1.1 About this document ......................................4
1.1.1 Retention and use ..........................................4
1.1.2 Copyright ........................................................4
1.1.3 Validity ............................................................4
1.1.4 Symbols and warnings ..................................4
1.2 Warranty ......................................................... 4
1.3 Limitation of liability ........................................4
1.4 Disposal of equipment ...................................5
1.5 Product key ....................................................5
1.6 Intended usage ..............................................5
1.7 Safety .............................................................6
1.7.1 Safety notices .................................................6
1.7.2 Responsibility of the user...............................6
1.7.3 Responsibility of the operator .......................7
1.7.4 User requirements .........................................7
1.7.5 Alarm signals ..................................................8
1.8 Technical Data ...............................................8
1.8.1 Approved operating conditions ......................8
1.8.2 General technical data ................................... 8
1.8.3 Specictechnicaldata ...................................9
1.8.4 Views ............................................................19
1.9 Construction and function ............................ 23
1.9.1 General description ...................................... 23
1.9.2 Block diagram ..............................................23
1.9.3 Scope of delivery .........................................24
1.9.4 Optional accessories ...................................24
1.9.5 The control panel (HMI) ...............................25
1.9.6 USB port (back side) ....................................27
1.9.7 “Sense” connector (remote sensing) ...........27
1.9.8 Ethernet port ................................................28
1.9.9 Analog interface ...........................................28
2
INSTALLATION & COMMISSIONING
2.1 Storage ......................................................... 29
2.1.1 Packaging ....................................................29
2.1.2 Storage ......................................................... 29
2.2 Unpacking and visual check ........................ 29
2.3 Installation ....................................................29
2.3.1 Safety procedures before installation and
use ................................................................29
2.3.2 Preparation ................................................... 29
2.3.3 Installing the device .....................................29
2.3.4 Connection to DC loads ...............................31
2.3.5 Grounding of the DC output ........................31
2.3.6 Connection of remote sensing ....................32
2.3.7 Connecting the analog interface .................32
2.3.8 Connecting the USB port (rear side) ...........32
2.3.9 Initial commission ......................................... 33
2.3.10 Commissionafterarmwareupdateora
long period of non-use .................................33
3
OPERATION AND APPLICATION
3.1 Personal safety ............................................34
3.2 Operating modes .........................................34
3.2.1 Voltage regulation / Constant voltage .........34
3.2.2 Current regulation / constant current / current
limiting ..........................................................35
3.2.3 Power regulation / constant power / power
limiting ..........................................................35
3.3 Alarm conditions ..........................................36
3.3.1 Power Fail ...................................................36
3.3.2 Overtemperature .......................................... 36
3.3.3 Overvoltage protection.................................36
3.3.4 Overcurrent protection .................................36
3.3.5 Overpower protection ..................................36
3.4 Manual operation .........................................37
3.4.1 Switching on the device ...............................37
3.4.2 Switching off the device ...............................37
3.4.3 CongurationviaMENU ..............................37
3.4.4 Adjustment limits (Limits) ............................. 45
3.4.5 Manual adjustment of set values .................45
3.4.6 Switching the main screen view ..................47
3.4.7 Switching the DC output on or off ................47
3.4.8 Recording to USB stick (logging) ................48
3.5 Remote control ............................................. 49
3.5.1 General .........................................................49
3.5.2 Control locations ..........................................49
3.5.3 Remote control via a digital interface ..........49
3.5.4 Remote control via the analog interface
(AI) ................................................................50
3.6 Alarms and monitoring ................................. 54
3.6.1 Device alarm handling .................................54
3.7 Control panel (HMI) lock ..............................55
3.8 Limits lock .....................................................55
3.9 Loadingandsavingauserprole ...............56
3.10 Other applications ........................................57
3.10.1 Series connection ........................................57
3.10.2 Parallel operation .........................................57
3.10.3 Operation as battery charger .......................57
4
SERVICE AND MAINTENANCE
4.1 Maintenance / cleaning ................................ 58
4.2 Faultnding/diagnosis/repair...................58
4.2.1 Replacing a defect mains fuse ....................58
4.2.2 Firmware updates ........................................58
4.3 Calibration ....................................................59
4.3.1 Preface .........................................................59
4.3.2 Preparation ................................................... 59
4.3.3 Calibration procedure ..................................59
5
CONTACT AND SUPPORT
5.1 Repairs .........................................................61
5.2 Contact options ............................................61

Elektro-Automatik PS 9000 T Series Specifications

General

Brand	Elektro-Automatik
Model	PS 9000 T Series
Category	Power Supply
Language	English