EasyManua.ls Logo

Elkay SOFT SIDES EDFPBM117WS User Manual

Elkay SOFT SIDES EDFPBM117WS
9 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
0000001029 (Rev. E - 06/16)
EDFPBM117WS EDFPBM117WS-F
Page 1
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain ttings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.
LZWS-EDFPBM117KEZWS-EDFPBM117K
SOFT SIDES
Fountains with FLEXI-GUARD
and EZH
2
O
®
Bottle Filler
INSTALLATION, CARE & USE MANUAL

Questions and Answers:

Elkay SOFT SIDES EDFPBM117WS Specifications

General IconGeneral
BrandElkay
ModelSOFT SIDES EDFPBM117WS
CategoryOutdoor Fountain
LanguageEnglish

Summary

Installer Information and Safety

Installation Cautions and Warnings

Essential safety advice for installers, including cautions on codes and warnings for service personnel.

Electrolysis and Grounding Considerations

Explains electrolysis effects and recommends plastic drain fittings to prevent water quality issues.

GFCI Requirement for New Installations

Mandatory use of Ground Fault Circuit Interrupter (GFCI) for all new installations.

Installation Procedures and Materials

Required Tools and Materials

Lists essential tools and materials required for the installation of the unit.

Installation Steps 1-7

Detailed instructions covering water supply, mounting frame, filter, and main panel installation.

Tube Routing Diagrams

Illustrations showing the correct tube routing for EZWS-EDFPBM117K and LZWS-EDFPBM117K models.

Further Installation Steps and Adjustments

Bottle Filler and Waste Connections

Instructions for connecting the bottle filler waste tubes and making final water supply connections.

Stream Height and Sensor Adjustment

Guidance on adjusting stream height for the bubbler and verifying bottle filler sensor operation.

Panel and Cover Plate Installation

Steps for installing cover plates, bottom panel, and optional panels.

Component Details and Diagrams

Bubbler Details and Notes

Diagram and notes for the Flexi-Guard bubbler detail, including tightening instructions.

WaterSentry Plus Filter Parts List

List of parts for the WaterSentry Plus filter system, including part numbers and descriptions.

Fountain Body and Push Button Assemblies

Exploded view diagrams illustrating the fountain body and push button assembly components.

Control Board Programming and Settings

Setting the Control Board

Instructions for verifying software, accessing programming buttons, and setting various parameters.

Filter Monitor and Bottle Count Reset

Procedures for resetting the filter monitor and the bottle count on the control board.

IR Sensor Range and Unit Type Settings

Guide to setting the IR sensor range and selecting the unit type (refrigerated or non-refrigerated).

Filter Capacity Setting

Instructions on how to set the filter capacity, choosing between 3000GAL or 6000GAL options.

Maintenance and Troubleshooting

Water Supply Connections and Parts

Diagrams and lists for water supply connections, overall parts, and bottle filler replacement kits.

Troubleshooting and Maintenance

Advice on mineral deposits, stream regulation, and general maintenance procedures.

Quick Connect Fittings Operation

Explanation of how to properly connect and disconnect tubing using quick connect fittings.

Related product manuals