Elkay SWIRLFLO FLEXI-GUARD ERPB2-8C User Manual

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC
97924C (Rev. A - 03/03)
Page 1
SWIRLFLO Refrigerated fountains with FLEXI-GUARD
INSTALLATION, CARE & USE MANUAL
TM
TM
!
CAUTION:
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
!
WARNING:
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
!
WARNING:
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an electrolysis effect occurring in the fountain. This may result in water which has a metallic
taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation. Any
drain fittings provided by the installer should be made of plastic which will electronically isolate the
fountain from the remainder of the buildings plumbing circuits.
ERPB2-8C ERPB2-8RAC

Elkay SWIRLFLO FLEXI-GUARD ERPB2-8C Specifications

General

Type	Outdoor Fountain
Model	ERPB2-8C
Material	Stainless Steel
Category	Outdoor Fountain
Mounting Location	Outdoor
Bubbler Activation	Push Button
Rated For Outdoor Use	Yes
Model Number	ERPB2-8C
Brand	Elkay
Product Line	SWIRLFLO FLEXI-GUARD
Mounting Type	Wall Mount
Power Source	Electric
Water Source	Municipal Water
Product Name	Elkay SWIRLFLO FLEXI-GUARD
Finish	Stainless Steel
Bottle Filling Activation	Sensor

Summary

Installer Information and Safety

Installation Cautions and Warnings

Essential safety advice and warnings for installers before and during unit installation.

Electrolysis and Water Quality Note

Information on potential water taste issues due to electrolysis caused by grounding.

Required Tools and Materials

Special Tools and Additional Materials

Lists of specialized tools and supplementary materials needed for installation.

Installation Procedures

Chiller and Water Supply Setup

Steps for installing the chiller and connecting the building's water supply.

ERPB/LRPB Plumbing Connections

Specific instructions for plumbing connections for ERPB and LRPB models, including cautions.

Fountain Panel and Body Mounting

Guidance on attaching upper and lower panels, and mounting the main fountain body.

Waste and Chiller Outlet Plumbing

Procedures for connecting waste tubes and the chiller outlet to the fountain.

Water Pressure and Stream Adjustment

Instructions for managing water supply pressure and adjusting the bubbler stream height.

Bubbler Assembly Details

Bubbler and Pedestal Installation Note

Note regarding the proper tightening of the bubbler and pedestal assembly.

Water Sentry Filter Assembly and Parts

Filter Assembly Diagram and Parts List

Diagrams and a detailed list of parts for the Water Sentry filter assembly.

Fountain Internal Assemblies

Fountain Body and Push Button Assemblies

Diagrams illustrating the components of the fountain body and push button assemblies.

Installation Package and Troubleshooting

Installation Package Contents

Details of the components included in the installation package for the units.

Water Supply Connections Diagram

Diagram illustrating water flow direction and service stop placement.

Troubleshooting and Maintenance Guidance

Advice on common issues like orifice assembly, stream regulation, and fitting operation.

Detailed Parts Identification

Comprehensive list of parts with item numbers, part numbers, and descriptions.