Emerson Bettis G Series - G01 Tool Style and Wrench Size

Installation, Operation and Maintenance Manual
VA-DC-000-1878 Rev. 0 December 2020
43
Section 6: Actuator Support Information
Actuator Support Information
Item
No.
G01
WT.
G2
WT.
G3
WT.
G4
WT.
G5
WT.
G7
WT.
G8
WT.
G10
WT.
Module
Description
3
lb N/A N/A N/A N/A N/A N/A N/A N/A
48” Dia. Power
kg N/A N/A N/A N/A N/A N/A N/A N/A
3
lb N/A N/A N/A N/A N/A N/A N/A N/A
52” Dia. Power
kg N/A N/A N/A N/A N/A N/A N/A N/A
5
lb 160 225 320 564 975 2,740 3,545 4,975
SR1 Spring
kg 73 102 145 256 442 1,243 1,608 2,257
5
lb 158 215 310 549 980 2,630 2,345 4,515
SR2 Spring
kg 72 98 141 249 445 1,193 1,064 2,048
5
lb 153 215 295 534 925 2,410 3,085 4,095
SR3 Spring
kg 153 98 295 534 925 2,410 3,085 4,095
5
lb 144 200 280 474 860 2,210 N/A 3,735
SR4 Spring
kg 65 91 127 215 390 1,002 N/A 1,694
5
lb N/A 200 N/A N/A N/A N/A N/A N/A
SRA5 Spring
kg N/A 91 N/A N/A N/A N/A N/A N/A
5
lb N/A 180 N/A N/A N/A N/A N/A N/A
SRA6 Spring
kg N/A 82 N/A N/A N/A N/A N/A N/A
7
lb 18 34 47 82 100 181 270 530
M18 SR
Override Cylinder
kg 8.2 15.3 21.2 36.9 45 81.45 1,275 239
2
lb 35 35 35 45 50 35 45 50
M18 SR Pump /
Reservoir
kg 14.5 14.5 14.5 20.4 22.7 14.5 20.4 22.7
6.3 G01 Tool Style and Wrench Size
Table 13. G01 Tool Style and Wrench Size
Item No. Wrench Size Item Qty.
Location or
Description
Recommended
Tool Style
1 - 110 9/16” 4 Hex Cap Screws Socket
1 - 160 1/2” 4 Hex Cap Screws Socket
1 - 180 3/8” sq. 2 Stop Screws Open End or Adjustable
1 - 190 1 - 15/16” 2 Hex Jam Nuts Open End or Adjustable
3 - 20 3/8” 2 Tie Bar (ats) Open End or Adjustable
3 - 40 3/8” sq. 1 Piston Rod Male Drive
3 - 90 1 - 1/8” 2 Standard Hex Nuts Socket
3 - 100 9/16” 4 Hex Cap Screws Socket
3 - 120 5/8” sq. 1 Pipe Plug Open End or Adjustable
3 - 130 3/16” 2 Socket Cap Screws Allen
5 - 20 9/16” 4 Hex Cap Screws Socket
7 - 80 9/16” 4 Hex Cap Screws Socket
7 - 110 1/8” sq. 1 Square Head Pipe Plug Open End or Adjustable
7 - 120 9/16” sq. 1 Square Head Pipe Plug Square Head Pipe Plug
12 1” 1 Breather Assembly Socket
13 3/4” 2 Vent Check Assembly Open End
- 3/8” sq. 1 Tension rod Male Drive