Emerson Fisher 4211 - User Manual

www.Fisher.com
D200354X012
Incorporates Errata Sheet dated February 2009 − see page 43
4200 Series Electronic Position Transmitters
Contents
Introduction 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scope of Manual 1. . . . . . . . . . . . . . . . . . . . . . . . .
Description 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 2. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Educational Services 2. . . . . . . . . . . . . . . . . . . . . .
Installation 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Special Instructions for Safe Use and
Installations in Hazardous Locations 6. . . . . .
CSA 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
FM 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ATEX Intrinsic Safety, Dust 7. . . . . . . . . . . . . . .
ATEX Type n, Dust 7. . . . . . . . . . . . . . . . . . . . . .
Mechanical Connections 7. . . . . . . . . . . . . . . . . . .
Sliding-Stem Actuator Mounting 7. . . . . . . . . . .
Rotary-Shaft Actuator Mounting 8. . . . . . . . . . .
Long Stroke Sliding-Stem Actuator
Mounting Type 585C and 470-16 8. . . . . . . .
Long Stroke Sliding-Stem Actuator
Mounting Type 585CLS and 490 9. . . . . . . .
Electrical Connections 10. . . . . . . . . . . . . . . . . . . .
Conduit 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Field Wiring 10. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Potentiometer Alignment 12. . . . . . . . . . . . . . . . .
Direct or Reverse Action 13. . . . . . . . . . . . . . . . . .
Operating Information 13. . . . . . . . . . . . . . . . . . . . .
Initial Considerations 13. . . . . . . . . . . . . . . . . . . . .
Transmitter and Position Switch
Conditions 15. . . . . . . . . . . . . . . . . . . . . . . . . .
Normal Operation 17. . . . . . . . . . . . . . . . . . . . . . . .
Calibration 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Test Equipment Required 17. . . . . . . . . . . . . . . . .
Test Connections to the Field Wiring
Compartment 18. . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter Circuit Zero and Span
Adjustment 18. . . . . . . . . . . . . . . . . . . . . . . . . . .
High and Low Position Switch Adjustment 19. .
Setting the High Position Switch 20. . . . . . . . . .
Setting the High Position Switch
Deadband 20. . . . . . . . . . . . . . . . . . . . . . . . . . .
Setting the Low Position Switch 20. . . . . . . . . .
Setting the Low Position Switch
Deadband 20. . . . . . . . . . . . . . . . . . . . . . . . . . .
Position Switch Circuit Shutoff 20. . . . . . . . . . . . .
Principle of Operation 21. . . . . . . . . . . . . . . . . . . . .
Transmitter Circuit 22. . . . . . . . . . . . . . . . . . . . . . .
Position Switch Circuit 22. . . . . . . . . . . . . . . . . . . .
W4273-1
SLIDING-STEM
ACTUATOR MOUNTING
W4274-1
ROTARY
ACTUATOR MOUNTING
Figure 1. Typical 4200 Series Position Transmitters
Maintenance 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Troubleshooting Procedures 23. . . . . . . . . . . . . .
Transmitter Circuit 23. . . . . . . . . . . . . . . . . . . . . .
Position Switch Circuit 24. . . . . . . . . . . . . . . . . .
Parts Ordering 27. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts List 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Loop Schematics and Nameplates 40. . . . . . . . . .
Introduction
Scope of Manual
This instruction manual provides installation,
operating, calibration, maintenance, and parts
ordering information for the 4200 Series electronic
position transmitters (figure 1). Refer to separate
instruction manuals for information on the actuator
and valve.
Instruction Manual
Form 5596
November 2006
4200 Series Transmitters

Emerson Fisher 4211 Specifications

General

Brand	Emerson
Model	Fisher 4211
Category	Transmitter
Language	English

Summary

Introduction

Scope of Manual

Outlines the scope of the instruction manual for the 4200 Series electronic position transmitters.

Description

Provides a general overview of the 4200 Series electronic position transmitters and their features.

Installation Procedures

Potentiometer Alignment and Action Setup

Procedures for aligning the potentiometer and setting direct/reverse action.

Mechanical Connections to Actuators

Details how to connect the transmitter to various types of actuators.

Maintenance

Troubleshooting Procedures

Parts Ordering

Specifications

Available Configurations

Lists the various available configurations for the 4200 Series transmitters.

Input;Output Signal Details

Details input signal sources and output signal characteristics of the 4200 Series transmitters.

Power and Performance Specifications

Covers power supply requirements, position switch relays, accuracy, repeatability, and operating influences.

Environmental, Safety, and Mounting

Details EMI compliance, operating conditions, mounting, electrical classification, housing, and weight.

Hazardous Location Installations

CSA Special Instructions

Provides special instructions for CSA hazardous area installations.

FM Special Instructions

Provides special instructions for FM hazardous area installations.

ATEX Approvals and Safety

ATEX Intrinsic Safety, Dust

Details ATEX intrinsic safety approvals and safe use conditions.

ATEX Type n, Dust

Details ATEX Type n approvals and safe use conditions.

Electrical Connections

Conduit Installation

Instructions for installing conduit according to electrical codes.

Field Wiring Procedures

Details field wiring connections for transmitter power and position switch circuits.

Transmitter and Position Switch Conditions

Normal Operation Overview

Describes normal operating behavior of transmitter and position switches.

Calibration

Test Equipment and Setup

Lists required test equipment and details test connections for calibration.

Transmitter Zero and Span Adjustment

Procedure for adjusting the zero and span of the transmitter output signal.

Position Switch Settings and Control

Procedure to adjust high/low switches, deadbands, and control circuit operation.

Principle of Operation

Transmitter Circuit Function

Details the internal workings of the transmitter circuit, including voltage regulation.

Position Switch Circuit Function

Explains how the position switch circuit operates and triggers relays.

Troubleshooting Procedures

Transmitter Circuit Troubleshooting

Procedures for troubleshooting issues within the transmitter circuit.

Position Switch Circuit Troubleshooting

Procedures for troubleshooting problems with the position switch circuits.

Printed Wiring Board Service

Transmitter Printed Wiring Board Removal and Replacement

Instructions for removing and replacing the transmitter's printed wiring board.

Component Replacement Procedures

Field Circuit Printed Wiring Board Service

Steps for removing and replacing the field circuit printed wiring board.

Pot;Bushing Assembly Replacement

Procedure for replacing the potentiometer and bushing assembly.

Parts List

Transmitter Common Parts

Lists common parts for transmitters with their part numbers.

Mounting Parts Lists

Type 470;471 Actuator Mounting Parts

Lists parts for mounting transmitters on Type 470/471 actuators.

Rotary Actuator Mounting Parts

Lists parts for mounting transmitters on rotary actuators.

Loop Schematics and Nameplates

CSA Intrinsic Safety Schematic

Provides the loop schematic for CSA intrinsically safe installations.

FM Intrinsic Safety Schematic

Provides the loop schematic for FM intrinsically safe installations.

Approval Nameplates

CSA and FM Approval Nameplates

Displays example nameplates for CSA and FM approvals.

ATEX Approval Nameplates

Displays example nameplates for ATEX approvals.