Page 15
When you are first learning to use the treadmill in conjunction with the
swim machine, it is best to start at the lowest speeds for both the swim
machine and treadmill. The added resistance the swim machine offers
may allow for a slower treadmill speed than initially thought.
IMPORTANT: Do not use treadmill when circulation pump is OFF.
PACE DISPLAY (OPTIONAL)
SWIM PACE DISPLAY - For any ENDLESS POOLS’ product that
generates a swim current the default setting
for the display is 100 meters (100 yard) pace
(shown as minutes:seconds). This indicates
the water flow equivalent of swimming 100
meters (100 yards) in a traditional lap pool in
the indicated amount of time. Swim current
units can also be for a 100 meter pace. As the current speed is
increased, the value the display reads goes down, since the faster you
swim the less time it takes to swim 100 meters (100 yards). Any Pace
Display can be set for a percentage of 2-100.
TREADMILL PACE DISPLAY - For the optional hydraulic treadmill the
default setting for the display is miles per hour.
The pace can be also be converted to display
kilometers per hour. Unlike a swim current
display, as the speed of the treadmill is
increased, the value on the display will also
increase. Any Pace Display can be set for a
percentage of 2-100.
QUICK START-UP INSTRUCTIONS
BEFORE YOU FILL YOUR FITNESS SYSTEM
Make sure your fitness system has been properly installed per all local
codes, including the location of the fitness system, the foundation of the
fitness system, as well as the electrical installation of the fitness system.
DO:
• Know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
• Have 5-way Test Strips Available.
• Have pH/Alkalinity Up & Down available.
• Know the hardness of your water, contact your dealer to help you
with this information. See Water Quality and Maintenance for more
information.
• Purchase the Clean Screen
™
pre-filter to remove unwanted
contaminants from the tap water. This is recommended, not required.
START-UP
Your ENDLESS POOLS fitness system has been thoroughly tested
during the manufacturing process to ensure reliability and long-term
customer satisfaction. A small amount of water may have remained in
the plumbing after testing and, as a result, may have spotted the fitness
system shell or the fitness system siding prior to delivery. Before filling
the fitness system, wipe the fitness system shell clean with a soft rag.
The following instructions must be read and followed exactly to ensure
a successful start-up or refill.
CAUTIONS
• DO NOT CONNECT POWER TO AN EMPTY Fitness System.
Power to the fitness system automatically activates critical
components within the fitness system, such as controls, heater, and
other systems. If power is supplied to these components prior to the
fitness system being filled, the components will be damaged, and this
may result in a non-warranty component failure.
• DO NOT use your fitness system after filling until all of the steps listed
below are completed.
• DO NOT add chlorine if treating your fitness system with
polyhexamethylene biguanide (Biguanide, PHMB, eg. BaquaSpa
®
)
sanitizer.
• DO NOT use a salt-generated chlorine system, this will damage
components and is not covered under your warranty.
• Before filling your fitness system for the first time, remove the
equipment compartment door and check to ensure that the unions on
either side of the pump(s) and heater are hand-tight and the slide
valves are open.
1. CLOSE DRAIN, remove the filter compartment grill skimmer
tray and one filter (pg. 26). Fill your fitness system through the
filter compartment using the CleanScreen
™
pre-filter (optional from
dealer) that attaches to your garden hose. The water level of your
fitness system should be maintained at a level 15 cm (6") below the
top of the fitness system. Reinstall the filter, skimmer tray, and grill
once the fitness system is filled.
IMPORTANT: Watkins Wellness does not recommend that the
fitness system be filled with “softened” water, as this may damage
the fitness system’s equipment.
2. AFTER THE FITNESS SYSTEM HAS BEEN FILLED with
water and the equipment compartment door is secured, power
must be applied to the fitness system.
• FIRST activate power to the subpanel from the main house panel.
• NEXT open the door of the electrical subpanel and reset the RCD
breakers.
• FINALLY, close and secure the subpanel door.
Getting Started
To Next Page
Loading...
Need help?
General
