Endress+Hauser Deltapilot S FMB70 Brief Operating Instructions

Endress+Hauser Deltapilot S FMB70

36 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

KA01026P/00/EN/14.13

71207396

Brief Operating Instructions

Deltapilot S

FMB70

Hydrostatic level measurement

These are Brief Operating Instructions.

For more detailed information, please refer to the Operating Instructions and the

additional documentation on the CD-ROM provided.

These Brief Operating Instructions are not intended to replace the Operating

Instructions provided in the scope of supply.

The complete device documentation consists of:

• these Brief Operating Instructions

• a CD-ROM with the Operating Instructions

Other manuals for Endress+Hauser Deltapilot S FMB70

Operating Instructions238 pages

Safety Instructions16 pages

Functional Safety Manual44 pages

Installation Instructions8 pages

Questions and Answers:

A
Andrea SparksJul 25, 2025
What to do if my Endress+Hauser Deltapilot S FMB70 device is not responding?
- K
  Kimberly WrightJul 25, 2025
  If your Endress+Hauser Measuring Instruments device is not responding, consider these potential causes and solutions: * The supply voltage might not match the specifications on the nameplate. If this is the case, apply the correct voltage. * The supply voltage might have incorrect polarity. If so, reverse the polarity of the supply voltage. * There might be no contact between the connecting cables and terminals. Check the contacting of the cables and correct if necessary.
E
Erika DiazAug 3, 2025
Why is there no display on my Endress+Hauser Deltapilot S FMB70 Measuring Instruments?
- D
  Dr. Jacob Mcgee DVMAug 4, 2025
  If there is no display on your Endress+Hauser Measuring Instruments, it could be due to several reasons: 1. The onsite display might be set too bright or too dark. To fix this, set the local display brighter by simultaneously pressing O and F, or set it darker by simultaneously pressing S and F. 2. The connector for the local display might not be plugged in correctly. Ensure the connector is properly plugged in. 3. The onsite display might be defective. If this is the case, replace the onsite display.
B
Billy JordanAug 15, 2025
Why is my Endress+Hauser Deltapilot S FMB70 Measuring Instruments Alarm Status not displaying the expected message priorities?
- P
  Paige Webb MDAug 15, 2025
  The Alarm Status/ALARM_STATUS parameter in Endress+Hauser Measuring Instruments shows the message with the highest priority. Check if the expected message has the highest priority.

Endress+Hauser Deltapilot S FMB70 Specifications

General

Output Signal	4...20mA HART, PROFIBUS PA, FOUNDATION Fieldbus
Application	Level measurement in liquids
Measuring Principle	Hydrostatic pressure
Measuring Range	Up to 100 m
Process Temperature	-40°C to +85°C (depending on version)
Process Pressure Absolute / Max. Overload Limit	Up to 40 bar (580 psi)
Housing Material	Stainless steel
Material	Stainless steel
Protection Class	IP68
Power Supply	10.5...45 V DC

Related product manuals

Preview: Deltapilot M FMB50

Deltapilot M FMB50

Preview: Deltapilot M FMB51

Deltapilot M FMB51

Preview: Endress+Hauser Deltabar S

Endress+Hauser Deltabar S

Preview: Endress+Hauser Deltabar S PMD75

Endress+Hauser Deltabar S PMD75

Endress+Hauser Deltabar S PMD70

Preview: Endress+Hauser Deltabar S FMD76

Endress+Hauser Deltabar S FMD76

Preview: Endress+Hauser Deltabar S FMD78

Endress+Hauser Deltabar S FMD78

Preview: Endress+Hauser Deltabar S FMD77

Endress+Hauser Deltabar S FMD77

Preview: Prosonic S FMU90 PROFIBUS DP

Prosonic S FMU90 PROFIBUS DP

Preview: Endress+Hauser Cerabar S PMP75

Endress+Hauser Cerabar S PMP75

Preview: Endress+Hauser Cerabar S PMP72

Endress+Hauser Cerabar S PMP72

Preview: Endress+Hauser Prosonic S FMU90

Endress+Hauser Prosonic S FMU90