To Next PageTo Next PageHow to troubleshoot incorrect current value in Endress+Hauser Laboratory Equipment?
If the current output of your Endress+Hauser Laboratory Equipment shows an incorrect current value, first check the adjustment using the integrated current simulation and connect a mA meter directly to the current output. The load may be too large, or there may be a shunt/short to ground in the current loop.
What to do if control signals are not accepted or outputs do not switch on my Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If control signals aren't accepted or outputs don't switch, the issue could stem from an incorrect program setting, so you should check the program setting. Incorrect wiring could also be the cause, so verify the wiring. In some cases, it may be due to electronics failure, and you may need to replace the basic module.
Why is my Endress+Hauser Laboratory Equipment not sampling?
If your device isn't sampling, it could be due to a connection leak, so check the tubes and connections for leaks. It may also be that the sampling hose is taking in air; ensure the sampling hose is routed correctly. If these steps don't resolve the issue, the wrong pump tube could be the cause, use only a genuine pump tube.
What to do if values appear on display but the display does not change and/or device cannot be operated on my Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If values appear on the display but the display doesn't change or the device cannot be operated, the module may not be wired correctly, check the modules and wiring. It could also be due to an impermissible operating system condition; try switching the device off and then on again.
Why is my sample not representative with my Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If your sample isn't representative, it could be due to a siphon in the sampling hose, so check the sampling hose. Another cause might be a connection that isn't airtight or a sampling hose taking in air; check the tubes and connections, and ensure the sampling hose is routed correctly. The wrong pump tube could be the cause, use only a genuine pump tube.
How to fix incorrect current value on the current output of my Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If the current output shows an incorrect current value, it might be due to incorrect adjustment. Check with integrated current simulation and connect an mA meter directly to the current output.
How to fix display values deviating from reference measurement on Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If the display values on your Endress+Hauser Laboratory Equipment are different from your reference measurement, there might be several reasons. First, the device may be incorrectly calibrated, in this case you should repeat the calibration and compare with the reference device. Second, the sensor could be dirty, in this case you should clean the sensor. Third, the temperature measurement may be incorrect, in this case you should check the temperature measured values of both devices. Finally, the temperature compensation settings may be off, in this case you should check the settings for temperature compensation and adjustment for both devices.
Why is there no current output signal from my Endress+Hauser Liquistation CSF48?
If there is no current output signal from your Endress+Hauser Laboratory Equipment, it could be because the base module is defective. Check with the integrated current simulation and connect a mA meter directly to the current output.
What to do if controller signals are not accepted on Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If the controller signals are not accepted or the outputs do not switch on your Endress+Hauser Laboratory Equipment, it could be due to an incorrect program setting. Check the program setting. Another possible cause is incorrect wiring, so check the wiring. If these don't solve the problem, the electronics may have failed, requiring you to replace the base module.
How to fix a dark display on Endress+Hauser Liquistation CSF48 Laboratory Equipment?
If your Endress+Hauser Laboratory Equipment shows a dark display, it could be due to no supply voltage. Check if the supply voltage is applied. Alternatively, the base module might be defective, in which case you should replace it.
General| Power supply | 100 to 240 VAC, 24 VDC |
|---|---|
| Cooling | Integrated cooling system |
| Housing material | Stainless steel |
| Communication | Ethernet |
| Protection | IP65 |
| Process Temperature Range | 0°C to 40°C |
| Protection Class | IP65 |
| Material | Stainless steel |
| Certification | CE |
