Endress+Hauser Liquisys M CCM223 - Table of Contents

Liquisys M CCM223/253 Table of contents
Endress+Hauser 3
Table of contents
1 Document information .............. 5
1.1 Warnings ............................ 5
1.2 Symbols used .......................... 5
1.3 Symbols on the device ................... 5
1.4 Electrical symbols ...................... 6
2 Basic safety instructions ............ 7
2.1 Requirements for personnel ............... 7
2.2 Designated use ........................ 7
2.3 Occupational safety ..................... 7
2.4 Operational safety ...................... 8
2.5 Product safety ......................... 8
2.5.1 State of the art .................. 8
2.5.2 IT security ...................... 8
3 Incoming acceptance and product
identification ....................... 9
3.1 Incoming acceptance .................... 9
3.2 Scope of delivery ....................... 9
3.3 Product identification ................... 10
3.3.1 Nameplate .................... 10
3.3.2 Product identification ............ 10
3.4 Certificates and approvals ............... 10
3.4.1  mark ...................... 10
3.4.2 CSA General Purpose ............. 10
4 Installation ....................... 11
4.1 Installation at a glance .................. 11
4.1.1 Measuring system ............... 12
4.2 Installation conditions .................. 14
4.2.1 Field device .................... 14
4.2.2 Panel-mounted device ............ 15
4.3 Installation instructions ................. 16
4.3.1 Field device .................... 16
4.3.2 Panel-mounted device ............ 18
4.4 Post-installation check .................. 18
5 Electrical connection .............. 19
5.1 Wiring ............................. 19
5.2 Electrical connection, version 1 ........... 19
5.3 Electrical connection, version 2 ........... 21
5.4 Device connection ..................... 22
5.5 Measuring cables and sensor connection .... 24
5.6 Three-point step controller for Cl
2
/ ClO
2
/
total chlorine ......................... 28
5.7 Alarm contact ........................ 29
5.8 Post-connection check .................. 29
6 Operation options ................. 30
6.1 Quick operation guide .................. 30
6.2 Display and operating elements ........... 30
6.2.1 Display ....................... 30
6.2.2 Operating elements .............. 32
6.2.3 Key functions .................. 32
6.3 Local operation ....................... 35
6.3.1 Automatic/manual mode .......... 35
6.3.2 Operating concept ............... 36
7 Commissioning .................... 38
7.1 Function check ....................... 38
7.2 Switching on ......................... 38
7.3 Quick Setup .......................... 40
7.4 Device configuration ................... 42
7.4.1 Setup 1 (chlorine/chlorine dioxide) .. 42
7.4.2 Setup 2 (temperature or pH/ORP) ... 44
7.4.3 Current input .................. 47
7.4.4 Current outputs ................. 51
7.4.5 Alarm ........................ 55
7.4.6 Check ........................ 56
7.4.7 Relay configuration .............. 60
7.4.8 Service ....................... 77
7.4.9 E+H Service .................... 79
7.4.10 Interfaces ..................... 80
7.4.11 Communication ................. 80
7.5 Calibration .......................... 81
8 Diagnostics and troubleshooting ... 85
8.1 Trouble shooting instructions ............. 85
8.2 System error messages .................. 85
8.3 Process-specific errors .................. 89
8.4 Device-specific errors ................... 93
9 Maintenance ...................... 95
9.1 Maintenance of the entire measuring point .. 95
9.1.1 Cleaning the transmitter .......... 95
9.1.2 Cleaning the pH/mV sensors
(EP version) ................... 96
9.1.3 Maintenance of chlorine sensors .... 97
9.1.4 Assembly ..................... 97
9.1.5 Maintenance of pH connecting
cables and junction boxes (EP
version) ...................... 98
9.2 Test and simulation .................... 98
9.2.1 Chlorine sensors ................ 98
9.2.2 Temperature measurement ........ 99
9.2.3 pH/ORP measurement ............ 99
9.2.4 Flow monitoring ................ 99
10 Repair ........................... 101
10.1 Spare parts ......................... 101
10.2 Disassembling the panel-mounted device ... 101
10.3 Disassembling the field device ........... 104
10.4 Replacing the central module ............ 107