What to do if the output current is less than 3.6 mA on my Endress+Hauser Transmitter?
If the output current is less than 3.6 mA on your Endress+Hauser Transmitter, it could be due to incorrect wiring of the signal line; check the wiring. Alternatively, the electronics unit may be defective, requiring you to replace the device.
What to do if my Endress+Hauser iTEMP TMT71 Transmitter is not responding?
If your Endress+Hauser Transmitter is not responding, there are several potential causes: * The supply voltage may not match what is specified on the nameplate. Use a voltmeter to check the voltage at the transmitter and correct it if necessary. * The connecting cables might not be making proper contact with the terminals. Check the cable connections and correct them if needed. * The electronics unit could be defective, requiring you to replace the device.
Why is there no display visible on my Endress+Hauser iTEMP TMT71 Transmitter?
If there is no display visible on your Endress+Hauser Transmitter, it could be due to the following reasons: * There is no supply voltage. Check the supply voltage at the head transmitter, terminals + and -. Also, make sure that the display module holders are correctly seated and that the display module is properly connected to the head transmitter. * The display module is defective and needs to be replaced. * The electronics of the head transmitter are defective, requiring you to replace the head transmitter.
How to fix HART communication not working on Endress+Hauser iTEMP TMT71?
If HART communication is not working on your Endress+Hauser Transmitter, consider the following: * A communication resistor may be missing or incorrectly installed. Ensure the communication resistor (250 ?) is correctly installed. * The Commubox might be connected incorrectly. Connect the Commubox correctly. * The Commubox may not be set to "HART". Set the Commubox selector switch to "HART".
What to do if the output current is less than 3.6 mA on Endress+Hauser iTEMP TMT71 Transmitter?
If the output current is less than 3.6 mA on your Endress+Hauser Transmitter, it could be due to: * The signal line is not wired correctly. Check the wiring. * The electronics unit is defective. Replace the device.
Why Endress+Hauser iTEMP TMT71 shows failure current (? 3.6 mA or ? 21 mA)?
If your Endress+Hauser Transmitter shows a failure current (? 3.6 mA or ? 21 mA), possible causes include: * A faulty sensor. Check the sensor. * The sensor is connected incorrectly. Connect the connecting cables correctly (terminal diagram). * Incorrect programming. Set the correct sensor type in the Sensor type device function.
Why is the display blank on my Endress+Hauser Transmitter?
A blank display on your Endress+Hauser Transmitter can occur for several reasons. It could be due to no supply voltage; check the supply voltage at the head transmitter, terminals + and -. Also, ensure that the display module holders are correctly seated and that the display module is properly connected to the head transmitter. If possible, test the display module with other suitable head transmitters, e.g. an Endress+Hauser head transmitter. Alternatively, the display module itself may be defective, requiring replacement. Lastly, the electronics of the head transmitter might be defective, necessitating replacement of the head transmitter.
General| Type | Temperature Transmitter |
|---|---|
| Housing Material | Aluminum or stainless steel |
| Input | RTD, TC |
| Output Signal | 4-20 mA HART, PROFIBUS PA, Foundation Fieldbus |
| Accuracy | ±0.1 °C |
| Ambient Temperature | -40 to 85 °C |
| Communication Protocols | HART, PROFIBUS PA, Foundation Fieldbus |
| Configuration | Via PC, Handheld terminal |
| Protection Class | IP66/67 |
| Sensor Type | RTD, Thermocouple |
To Next Page
