To Next PageTo Next PageWhat to do if my Endress+Hauser Proline Prosonic Flow B 200 Measuring Instruments device measures incorrectly?
If your Endress+Hauser Measuring Instruments device is measuring incorrectly, it could be due to a configuration error or because the device is being operated outside of its intended application. First, check and correct the parameter configuration. Second, observe the limit values specified in the "Technical Data".
Why is the signal output outside the valid range for my Endress+Hauser Measuring Instruments?
If the signal output is outside the valid range for your Endress+Hauser Measuring Instruments, the main electronics module could be defective. In this case, you should order spare part ? ? 124.
Why is the local display dark and there are no output signals on my Endress+Hauser Measuring Instruments?
The local display might be dark with no output signals on your Endress+Hauser Measuring Instruments due to several reasons: * The supply voltage doesn't match the nameplate specifications, so you should apply the correct supply voltage. * The supply voltage polarity is incorrect, thus you should reverse the polarity. * There's no contact between connecting cables and terminals, so check and correct the cable connections if needed. * The terminals aren't correctly plugged into the I/O electronics module, so check the terminals. * The I/O electronics module is defective, in which case you should order spare part ? ? 124.
What to do if the local display is dark but the signal output is within the valid range on my Endress+Hauser Measuring Instruments?
If the local display is dark, but the signal output is within the valid range on your Endress+Hauser Measuring Instruments, it could be due to a few reasons: * The display is set too bright or too dark. To set the display brighter, simultaneously press ? + ?. To set the display darker, simultaneously press ? + ?. * The cable of the display module is not plugged in correctly. Insert the plug correctly into the main electronics module and display module. * The display module is defective. In this case, order spare part ? ? 124.
How to fix no write access to parameters on Endress+Hauser Measuring Instruments?
If you have no write access to parameters on your Endress+Hauser Measuring Instruments, it might be due to: 1. Hardware write protection being enabled: Set the write protection switch on the main electronics module to the OFF position. 2. The current user role having limited access authorization: Check the user role ? ? 46 and enter the correct customer-specific access code ? ? 46.
What does it mean if the backlighting of local display is red on Endress+Hauser Proline Prosonic Flow B 200 Measuring Instruments?
If the backlighting of the local display is red on your Endress+Hauser Measuring Instruments, it indicates that a diagnostic event with "Alarm" diagnostic behavior has occurred. Take remedial measures ? ? 112.
How to resolve a "Communication Error" message on the local display of Endress+Hauser Proline Prosonic Flow B 200?
If you see a "Communication Error" message on the local display of your Endress+Hauser Measuring Instruments, it means that the communication between the display module and the electronics is interrupted. Check the cable and the connector between the main electronics module and display module. If the problem persists, order spare part ? ? 124.
How to resolve text on local display appearing in a foreign language and cannot be understood on Endress+Hauser Proline Prosonic Flow B 200?
If the text on the local display appears in a foreign language and cannot be understood on your Endress+Hauser Measuring Instruments, it means that an incorrect operating language is configured. To fix this: 1. Press ? + ? for 2 seconds ("home position"). 2. Press ?. 3. Set the desired language in the Language parameter.
How to fix no connection via HART protocol on Endress+Hauser Proline Prosonic Flow B 200?
If there is no connection via HART protocol on your Endress+Hauser Measuring Instruments, it may be due to: * A missing or incorrectly installed communication resistor. Install the communication resistor (250 ?) correctly and observe the maximum load ? ? 26. * Issues with the Commubox, such as incorrect connection, configuration, driver installation, or USB interface configuration. Refer to the Commubox documentation ? FXA195 HART: Document "Technical Information" TI00404F.
Why is the signal output outside the valid current range (< 3.6 mA or > 22 mA) for my Endress+Hauser Proline Prosonic Flow B 200?
If the signal output is outside the valid current range (< 3.6 mA or > 22 mA) for your Endress+Hauser Measuring Instruments, the I/O electronics module is likely defective. Order spare part ? ? 124.
General| Brand | Endress+Hauser |
|---|---|
| Model | Proline Prosonic Flow B 200 |
| Category | Measuring Instruments |
| Language | English |
