Endress+Hauser Proline Prosonic Flow P 500 User Manual (English)

Other manuals for Endress+Hauser Proline Prosonic Flow P 500

Operating Instructions224 pages

Manual80 pages

Technical Information88 pages

Questions and Answers:

B
Brittany KeithAug 20, 2025
Why is write access to parameters not possible on Endress+Hauser Measuring Instruments?
- B
  Brendan DuncanAug 20, 2025
  If the write access to parameters is not possible on your Endress+Hauser Measuring Instruments, it may be due to hardware write protection being enabled. To resolve this, set the write protection switch on the main electronics module to the OFF position. Alternatively, the current user role might have limited access authorization. In this case, check the user role or enter the correct customer-specific access code.
E
ericmyersAug 25, 2025
What does "Communication Error" mean on Endress+Hauser Measuring Instruments?
- A
  Andrew GoodAug 25, 2025
  If the message "Communication Error" "Check Electronics" appears on the local display of your Endress+Hauser Measuring Instruments, it indicates that communication between the display module and the electronics has been interrupted. To resolve this, check the cable and the connector between the main electronics module and display module. If the problem persists, you may need to order a spare part.
C
Calvin MitchellAug 26, 2025
How to fix unable to connect to the web server on Endress+Hauser Proline Prosonic Flow P 500 Measuring Instruments?
- E
  Elizabeth MortonAug 26, 2025
  If you are unable to connect to the web server of your Endress+Hauser Measuring Instruments, it may be because the web server is disabled. Using "FieldCare" or "DeviceCare", check whether the web server of the measuring device is enabled, and enable it if necessary. It could also be due to an incorrectly configured Ethernet interface or IP address on your PC; check these settings. Alternatively, the WLAN access data may be incorrect; verify the WLAN network status and log on to the device again, ensuring WLAN is enabled on both the measuring device and operating unit.
T
Thomas JohnsonAug 28, 2025
What to do if local display cannot be read on Endress+Hauser Proline Prosonic Flow P 500?
- J
  Jerome YorkAug 28, 2025
  If the local display of your Endress+Hauser Measuring Instruments cannot be read, but the signal output is within the valid range, the display might be set too bright or too dark. Try setting the display brighter by simultaneously pressing the indicated buttons, or darker by pressing the other indicated buttons.
L
Lori FryeAug 29, 2025
Why is the local display dark but signal output valid on Endress+Hauser Proline Prosonic Flow P 500 Measuring Instruments?
- M
  Mark GriffinAug 29, 2025
  If the local display of your Endress+Hauser Measuring Instruments is dark, but the signal output is within the valid range, it may be because the cable of the display module is not plugged in correctly. Ensure the plug is correctly inserted into both the main electronics module and the display module.
G
grahammichaelSep 1, 2025
Why is web browser content difficult to read on Endress+Hauser Measuring Instruments?
- D
  David BuckSep 1, 2025
  If the web browser content display is difficult to read or incomplete on your Endress+Hauser Measuring Instruments, it may be due to using a web browser version that is not optimal. Use the correct web browser version, empty the web browser cache, and restart the web browser. Unsuitable view settings can also cause this issue; try changing the font size or display ratio of the web browser.
T
Thomas GomezSep 3, 2025
How to change the language on Endress+Hauser Proline Prosonic Flow P 500 display?
- J
  James KlineSep 3, 2025
  If the text on the local display of your Endress+Hauser Measuring Instruments appears in a language that you cannot understand, it is likely that the selected operating language is not correct. To change it, press the indicated buttons for 2 seconds to reach the "home position", then press the other indicated button, and configure the required language in the Display language parameter.
S
Steven DavisSep 5, 2025
Why is the network connection not present or unstable on Endress+Hauser Proline Prosonic Flow P 500 Measuring Instruments?
- F
  friedmancodySep 5, 2025
  If you are experiencing a network connection that is not present or unstable with your Endress+Hauser Measuring Instruments, it could be due to a weak WLAN network. Check the network status on the operating unit, and consider using an external WLAN antenna to improve network performance if the operating unit is outside the reception range. Another possible cause is parallel WLAN and Ethernet communication; check the network settings and temporarily enable only the WLAN as an interface.
M
Mary MurphySep 7, 2025
Why is the backlighting of local display red on Endress+Hauser Proline Prosonic Flow P 500 Measuring Instruments?
- J
  Jeremy ClineSep 7, 2025
  If the backlighting of the local display of your Endress+Hauser Measuring Instruments is red, it indicates that a diagnostic event with "Alarm" diagnostic behavior has occurred. Take remedial measures.
J
Jared HermanSep 9, 2025
What to do if web browser is frozen on Endress+Hauser Measuring Instruments?
- M
  Mark EvansSep 9, 2025
  If the web browser is frozen and operation is no longer possible with your Endress+Hauser Measuring Instruments, it could be because data transfer is active. Wait until the data transfer or current action is finished. Alternatively, the connection may have been lost; check the cable connection and power supply, and refresh the web browser, restarting it if necessary.

Endress+Hauser Proline Prosonic Flow P 500 Specifications

General

Device Type	Ultrasonic flowmeter
Protection Class	IP66/IP67
Measurement Principle	Transit time difference
Accuracy	±0.5% of measured value
Process Temperature	-40°C to +80°C
Process Pressure	Max. 40 bar
Output	4...20 mA, pulse output, frequency output
Communication Protocols	HART
Power Supply	24 V DC
Wetted materials	Stainless steel
Transmitter housing	Aluminum
Display	LCD
Approvals	ATEX, IECEx
Weight	Approx. 5 kg